Dodge Journey Dashboard Warning Lights (All Models 2009 to 2020)
Welcome to the ultimate guide to all dashboard symbols, warning lights, errors and faults for the 2000 to 2020 Dodge Journey. This will assist in troubleshooting, diagnosing and solving common automotive problems with this specific car.
Please note: This guide covers every single possible symbol/warning light for ALL model variations for Dodge Journey, including standard, premium and top-of-the-line models, plus variations in body shape. While this guide does cover your specific vehicle , your car may not have all the symbols featured on this list.
Dodge Journey Symbols and Warnings Guide
There are 25+ possible lights that may illuminate for a variety of reasons.
While this guide is helpful, please refer to your owner’s manual after reading through this list.
Dodge Journey Engine Fault
There are hundreds of reasons why the check engine warning fault light comes on, and only your dealer or mechanic is qualified to address this.
Common reasons include a loose fuel cap, excess vibration, a blocked cylinder, a bad fuel mix, excessive heat and half power.
This may also highlight an issue with your transmission.
Dodge Journey Check Engine Oil
This means your engine oil is running low or has been completely drained. Your engine may have an extensive oil leak and a mechanic will be required urgently.
At this stage, it’s not recommended that you drive your vehicle.
Dodge Journey Attention / Warning / Fault Detected
Either of these two lights will illuminate to get your attention to other dashboard warning lights and symbols.
These lights can also mean that the handbrake is engaged.
Dodge Journey Battery
This means your battery has low voltage and may need a replacing.
Should you choose to drive your vehicle with a faulty battery, you risk losing power to your battery at high speeds.
Many mechanics will prefer to visit your home to replace your car’s engine battery, rather than have you drive to them.
Dodge Journey Press Foot Brake
This symbol is your Dodge Journey telling you to press the foot brake.
This is required before starting the engine and moving the vehicle out of Park.
Dodge Journey Handbrake Engaged
Your handbrake is engaged.
This can be disengaged by hand, or your vehicle may have a handbrake that is disengaged with your foot.
Dodge Journey Airbag Fault
This means your driver’s side or passenger side airbag has a fault and may not deploy when required. However, it’s quite common for this light to illuminate due to a faulty sensor, rather than a faulty airbag.
Take your vehicle to your mechanic for inspection as soon as possible.
Dodge Journey High Radiator Coolant Temperature
This symbol represents excessive heat from your engine’s radiator. If ignored, you risk overheating your engine very quickly.
Common reasons are a low coolant level and a leak in the radiator.
Call or visit a mechanic immediately.
Dodge Journey Parking Sensors
This symbol represents the front or rear parking sensors. You will also hear an audible beep as you get closer to a wall, pole, tree or other object when reversing.
Dodge Journey Bulb Not Working
This means one of your driving lights has stopped working and requires either a bulb replacement or fuse replacement.
Dodge Journey Low Beam Lights On
This means your front standard driving lights are on.
These lights are used for 99.9% of driving.
Dodge Journey High Beam Lights On
This means your front high-beam driving lights are on.
These lights are used for 0.01% of driving and typically for country roads late at night. Fines can apply for use of high beams in dense residential areas. Do NOT use high team driving lights within 400 metres (1,000 feet) of an oncoming car.
Dodge Journey Automatic Low Beam Lights On
This means your front automatic standard driving lights are on.
These will illuminate by themselves on dusk, when entering tunnels and in other low light situations.
Dodge Journey Automatic High Beam Lights On
This means your front automatic high-beam driving lights are on.
Please be wary that these lights do not turn themselves on automatically around other cars.
Dodge Journey Automatic Lights Malfunction
Dodge Journey’s come with automatic lights, however, these can malfunction.
This is often an issue with the front low-light sensor. You may continue to drive and simply use your normal on/off headlight function until you visit a mechanic.
Dodge Journey Glow Plug Indicator Symbol
This is the Glow Plug Indicator symbol, which is found only in diesel-powered variants of Dodge Journey. Diesel engines require heat in the cylinders to operate, which is supplied initially by its glow plugs when the engine is freezing cold.
When illuminating green, this is operating perfectly but when yellow, a fault may exist.
Dodge Journey Vehicle Is In Park
This means your vehicle is in Park.
Dodge Journey Hood / Bonnet Is Open
While your front hood/bonnet may appear closed, it may show open on the sensor.
Dodge Journey Front Fog Lights Enabled
This means your Dodge Journey front fog lights are engaged. A similar symbol exists for the rear warning lights.
Note: In some areas, it is illegal to use fog lights when it isn’t foggy. Please check with your local authority.
Dodge Journey ABS System Fault / ABS System Off
Your vehicle’s ABS system has a fault and may not engage under heavy braking.
Please visit a mechanic as soon as possible.
Dodge Journey ECO Mode On
ECO mode in a Dodge Journey is an optimum driving mode.
Your throttle will not respond favorably to performance driving.
Instead, your fuel economy will be at its best, hence the term ‘Eco’.
Dodge Journey Truck / Boot Open
While your rear trunk/boot may appear closed, it may show open on the sensor.
Dodge Journey Front Radar Engaged
This means your front sensor is engaged.
This feature provides autonomous braking and adaptative cruise control.
Dodge Journey Lane Assistant On
This means your lane-keeping assistant is on.
This feature allows your vehicle to remain straight within its lane.
This may only engage above 40km/h or 25mp/h.
Dodge Journey ESP / ESC Engaged
This means your Dodge’s Electronic Stability Programme (or Electronic Stability Control in some countries) has been engaged.
This typically engages on wet, muddy or icy roads.
Dodge Journey Check Brake Fluid
This means your brake fluid has become low and may require topping up.
Dodge Journey Check Brake Pads
This means your brake pads have become low.
This may be difficult to check and may require visiting a mechanic as soon as possible.
Dodge Journey Steering Wheel Locked
This means your steering wheel is locked.
This is an anti-theft symbol that flashes when your vehicle is locked.
Dodge Journey Service Due Soon
This means your vehicle is due for servicing soon.
Your mechanic may have programmed an alert within your car’s computer to illuminate this symbol upon crossing a certain odometer reading.
Dodge Journey Heated Seats
This means your heated seats are on.
The number of vertical lines represents the level of heat.
Dodge Journey Cruise Control Activated
This means your cruise control has been activated and is ready to use.
However, your cruise control will not be on. It’s simply ready to switch on.
Cars often use 2-buttons to avoid accidentally turning on cruise control.
Dodge Journey Check Wheel
This means you have an issue with your wheel.
This isn’t the rubber tire but the wheel itself.
Issues include alignment, steering and balance.
Dodge Journey Heated Windscreen
This means your windscreen is being heated to melt frost or ice.
This may turn itself off automatically.
Dodge Journey Air Suspension Fault
If your Dodge Journey has air suspension, then this symbol represents a fault.
This could be a deflated rear suspension air bag, an air leak or a sensor issue.
Dodge Journey Tire Air Pressure Fault
This means your tire pressure is either too low, or the sensor has faulted.
This requires calling or visiting your dealership as soon as possible.
Dodge Journey Intermediate Windscreen Wipers On
This means your automatic windscreen wipers are on. No action is required.
Ultimately, your car is trying to tell you something. You should consult your owner’s manual and have your car inspected by a qualified mechanic as soon as possible.
Symbols Have Different Colors
Much like traffic lights, the color of your dashboard symbol light is just as important as what it means. The lights can also flash to draw your attention to a more severe and time-sensitive issue.
When a Dodge dashboard warning light is green or blue, they are simply telling you that one of your car’s features is being used, or has been activated. No action is required at this time.
When a light is yellow, your car is trying to tell you that a less common safety feature of the car is being used (such as stability control on wet roads), a mild fault has been detected or a repair may be required. If you’re unsure, you should seek the services of a mechanic or dealership as soon as possible.
Orange or Red
If the dashboard on your Dodge is orange or red, this can be a signal that your vehicle is experiencing a problem that needs urgent attention . You MUST call or visit your dealership or mechanic immediately.
This dashboard symbols guide is for entertainment and informational purposes only, and does not replace seeking professional advice from a certified technician or expert mechanic. Please consult with a certified technician or mechanic if you have specific questions or concerns relating to any of the topics covered herein. Under no circumstances will DashboardWarningsLights.com be liable for any loss or damage caused by your reliance on any content on this website.
Joshua Lee is the writer, editor and owner of DashboardWarningLights. Joshua has a deep obsession with the automotive industry, for both passenger vehicles and trucks. When he isn't writing or driving, he enjoys exploring in the great outdoors!
DASH-LIGHTS.COM
Dashboard Warning Lights Explained
Dodge Journey Dashboard Warning Lights
64 thoughts on “ dodge journey dashboard warning lights ”.
My dash board lights only goes off for like 10minutes and then comes back on permanently after turning off the engine and locking the car doors. this drains my battery
I got a warning light that I can’t find in my manual or on line. It looks like a screw in the side of the vehicle. Can you tell me what it means?
Hello Patricia, Are you sure the car and screw warning light is not a loose gas cap symbol?
I checked these on mine but did not affect car with large screw hovering.
I just got that light today…is it the gas cap
Put antifreeze in the car gauge says the oil temperature is rising the transmission fluid temperature is rising and the coolent temperature is rising and says 5470 engine hours what does this mean
Hi Wanda, How old is the existing antifreeze? If it’s several years old, it may require flushing, else there may be sludge build up resulting in the system getting blocked. Transmission systems can also make use of the car’s cooling system and can overheat if there’s a problem. Also check your char’s water pump. The engine hours is referring to how many hours your engine has been in operation over its lifetime.
Patricia I had the dame this last week and even the mechanic had never seen it I checked the gas cap, took if , screwed it in again, but no change. Had the lugs tightened on wheels though he said they were fine= zi have NO IDEA. It bothers me that it’s not in the manual
2014 Dodge Journey: 3 warning lights came on simultaneously. Oil which is full, tired which are filled to spec. and eve light. What causes this and how do I fix it?
Hi Tom. Rather than ‘eve light, did you mean ABS light? Sounds like sensor issues. I would concentrate on the oil light initially as this is the most serious and have your engine pressure checked. If it’s good, it may be the oil pressure sensor.
My 2009 Dodge Journey’s instrument panel completely lights up when shifting from 1st to 2nd. You can feel a slight jerk and click. Tranny works fine but the dashboard is completely lit up. I already reset the dashboard but it comes on immediately when shifting from 1st to 2nd.
Round red light came on three times went out each time what is this red dot panel with rpm’s
Hi Yolanda. I think it’s the vehicle security warning light. Have you changed or disconnected the battery?
I have a 2009 Journey. Sporadically, the ESC light will come on, and the car starts running very rough….almost to the point of stalling. However, if I keep a steady flow of gas, it doesn’t stall on me. Do you know how the gas and ESC error light would be related causing the car to run so badly? Thank you!
Hi Amy, Part of the ESC (Electronic Stability Control) system is to cut engine power and can also apply braking. This helps with traction (preventing wheel spin), oversteer and understeer. If the system is faulty, it could be engaging when it’s not supposed to and giving you the rough engine and problems accelerating. This could be something as simple as a wheel speed sensor that’s at fault, or the ESC module, steering angle sensor.
On my dashboard. Red light came on.and i can’t find the red light symbol.i have a 2010 dodge journey.i have look up the symbols on my phone and i can’t find that symbol.
Hi Loretta Can you describe the light?
I’m having a similar problem as Amy. Sometimes my ESC light will come on and it says OFF though. Basically ESC OFF it shows the image, but it says OFF. It happened today. I turned on the car and the light came on and I had to get in the interstate and I was going 70+MPH and whenever I would let my foot off the gas and the vehicle would stutter and feel like it wanted to stall. The MPH would begin to drop and I wasn’t able to increase by speed. It would drop to about 60 MPH and then I would be able to increase by speed again..I have a 2011 Journey.
I am having the same problem…did you ever figure out how to fix it??
2018 Dodge Journey check engine light and it woo t switch gears. It will jerk really hard then it won’t switch gears
I have a flashing “Dodge” symbol that flashes then remains on for a short time. The tipm has been replaced. Could it be a reset is needed?
What does red ‘Back’ light mean
what does it mean when the letters PSI come on?
On my 2010 Dodge Journey. The Eps light is staying on
My dodge journey yellow light has just come up. Although today I’ve had new tyres and rims fitted have you any idea as to why if so any help will be appreciated thanks
Hello Kelly, I assume you mean the tyre pressure warning light? The tyre pressure light coming on after having new tyres fitted is usually a sign that a sensor has not been fitted, not been fitted correctly or damaged during the tyre fitting service.
I have a stupid question! Do I turn on the slippery car symbol when I’m driving in the snow?
Hi Janie, No, don’t touch it, it will automatically be on already. If you press the button so that the slippery car symbol illuminates, you’ll be switching the system off. On most cars it’s called electronic stability control (ESC) or something similar. ESC comes on automatically each time you start the car.
If you happen to get stuck in snow and can’t get out, you might need to rock the car backwards and forwards. In this situation, you press the ESC button (slippery car symbol), or the traction control button to deactivate traction control. By leaving traction control on, it’ll stop or reduce wheel slip, but if you’re stuck in snow, you want wheel slip to help free your vehicle. Once you’re free from the snow, press the button again to switch on ESC.
Hello, I have a 2016 journey and I get the ETC and the ESC indicators on. Usually I pull over, turn off the car and wait a few seconds but now it’s happening more often. What is this and how can I fix it?
Hello, my ETC and my ESC have started to come on, more in the past 2 days. What should I do to fix this? I have changed the alternator and the battery and it still keeps coming on
Hello Al, The throttle sensor is quite a common fault with the Dodge Journey. The throttle body might need to be replaced.
My etc light came on and now the car isn’t starting what do i do? its not even turning its my moms car and she’s on vacation
Is the car turning over? Things to check are battery charge and connectors. Throttle body is often an issue, sometimes to do with the sensor.
Hello, I have a 2014 journey and I get the ETC and the ESC indicators on. Usually I pull over, turn off the car and wait a few seconds but now it’s happening more often. What is this and how can I fix it? Now it barely even starts half the time what is wrong?
Hi Angel, It’s usually to do with the throttle body. Usually throttle control sensor or position sensor, sometimes the wiring. An issue with the throttle may disable the ESC, so sorting out the throttle issue is likely to fix the ESC issue.
Battery died.Had it jumped.Cars great never any problem. We under reaio are buttone to push for Air, a C button, from, rear ans slippery traction. We t g we button next to air that has C on it bliks :& I don’t know ow if could be a fuse of something more serious My husband fixed these problems but he passed suddenly 90 days ago Can someone answer my question please. I’m in Florida and you can’t dive In aug8with no circulating air. I’m at [email protected]
I have a 2011 journey with 131791 miles on it for the 1st time since owning it in the little center window it’s showing what gear I’m in p r d but it also has a round clock like light right next to the gear light what does that mean I have had nothing but problem’s with this piece of junk the Camara quit heated seats quit had to replace a heater core had to replace head gaskets battery altanator brakes every 1 1/2 years in front worse car ever owned some how front drive shaft got bent or something so the whole car,s vibration was so bad you could not drive the thing .
Hi Dean, Sounds to me like you need to get rid of ASAP. I’m afraid I’m not too sure. Looked into it and can’t find any info. All I can think is that it’s symbol of a reminder – maintenance / service? Hopefully someone else will know.
Hi, there. When I was driving my 2014 Dodge Journey on hyw feeling the car was shaking, I could see my arms were shaking, about half hour later sign on the middle screen looks like a double lined Red Cross while a Ding sound, and disappear soon. Then I got out the Hyw, the shaking was disappeared on 50km/h. Anyone know what’s the sign for? Just changed my tires at Costco three month ago.
I have a 2014, when I put it in reverse a over look of the vehicle comes up on the dashboard with a SERVICE light under it and a dinging sound comes on. This has been going on for awhile, the rear camera works fine and has not ever been damaged. Any ideas on if this is a normal thing or is it something more?
My 2012 journey has a small red polite and a exclamation icon red in colour be for it what does it mean can’t find a explanation any were it is on the rite round dash gauge thanks
Hello everyone while reversing today for my dodge Journey 2018, I noticed a sign came up on the reverse showing clean what does that mean
Hi Teddy, Could it be to do with the backup camera or ParkSense sensors that need cleaning? The ParkView camera is located on the rear of the vehicle above the rear license plate and the outer surface and the underside of the rear fascia/bumper require cleaning and kept clear of snow, ice, mud, dirt or other obstruction for the ParkSense sensors.
I have a 2015 diligence journey. Every now & then going downhill I get an ! Mark and a P. Both are in red circles. Mai
Hi Mai, I should have your vehicle braking system serviced. Always best to have anything to do with brake issues checked out right away. It is worth checking under the hood at your brake fluid levels, as this level will fall over time as brake pads wear low. Also keep an eye on brake pads, they require replacing after a while.
The ETC Light and the traction light lit up. What does this mean? Is it because my air tire pressure is low?
Hi Betsy, It’s unlikely to be related to tire pressure, but it’s best to keep tire pressures up to the recommended values as stated on the sticker inside the door jamb. This will improve stability and fuel consumption. The Dodge Journey does have issues with the throttle body, often needing replacement. This fault can trigger reduced engine power mode (limp home mode) and often systems such as traction control can be automatically deactivated as a result.
What is the small red P with a ! Red icon be for it mean on my 2012 dodge journey it is in the rite round dash gauge
Hi Doug, I’m not sure either I’m afraid. All I can think of is a problem with Park (P). If it would be parking brake related, it would be contained in a circle and parenthesis.
In 2014 dodge journey..the inside lights flashed on and off for 2 minutes while dash had a dinging sound..stopped for a minutes started again..lasted 15 minutes til I got home.. what’s this mean??
Hi Alicia, Is it a specific timed flashing or more of a sporadic flickering? There are some issues with Dodge Journey’s with flicker interior lights, or lights staying on which is related to bad wiring / short issues. A wire that controls lighting to the trunk is a common culprit.
Hit a large pothole and now the ads light along with other lights come on. Sometimes the lights will come on when turning on the ignition and other times it does not. I was told that this could be a wheel bearing problem or an ABS shortage anyone have any ideas.
Hi Eugene, Yes, as you say, wheel bearing is a possibility. There’s also a wheel speed sensor located at each wheel, these sensors are prone to damage and that could also be the issue. If you’re noticing any noise from the particular wheel that hit the pothole, humming noise, looseness in the steering, vibrations etc, this may also be a symptom of a damaged wheel bearing.
Hi I have a 2014 dodge journey and my engine light came on and hasn’t gone off I had a service last week and nothing was bought to my attention. We had a -1 degree morning and the car was frozen could this have an impact on this light coming on?
Hi Kelly, Yes the colder weather can impact on your car. Usually though, it’s the cold weather, triggering the engine light that’s making an already underlying problem worse, hence the light. There’s no way of knowing why the engine light is on other than having diagnostics. When the engine light comes on, you’ll typically have a fault code generated and stored. A diagnostic OBD II tool is used to scan for the codes and point you to where the fault is. You should be able to find an auto workshop where you’ll receive a free diagnostics check.
I had a Throttle Replacement a month ago, for my 2014 Dodge Journey with 67,000 miles at the Dealership. No w, a red sailboat light with a chime just came on. What could this mean. Please help, thank you!
Hi Dionne, A sailboat light? It’s not the engine coolant light is it? (see above)
Hi My Dodge Journey stx 2012 model 3,6 shows slippery Warning light, ABS, Brake and constantly feels like its going to cut but doesn’t cut at all. What it might be?
Hi Xolani, I should check your brake fluid level. A common cause for the ABS and slip indicator light to come on is a faulty wheel speed sensor. However, as your brake light is illuminated, you should have any fault codes read with a diagnostic scanner right away.
Leave a Reply Cancel reply
Your email address will not be published. Required fields are marked *
Vehicle Manufacturers
- Mercedes-Benz
Vehicle Type
- Commercial Vehicles
Warning Lights
- Dash Warning Lights
- Car Warning Light Colour Meaning
- Privacy Policy
Dodge Journey Dashboard Lights And Meaning
Dodge Journey is a crossover SUV car marketed by FCA’s Dodge Brand (2009) that gives you a potent engine along with Low starting price. Its infotainment system is so trouble-free to operate with more user -friendly technical features.
This car highly appealed to a next-level performance with comfy driving. It comes with an excessive lean body that makes its infrastructure more stylish and upgrades your status.
Such trendy cars are composed with so many warning indications displayed on the car’s dashboard. It highlights the malfunctioning of the system’s components, security issues, and immediate maintenance whenever needed. It is highly suggested not to neglect these lights as it can risk the safety of the driver.
Look below the warning lights that demonstrate the respective meanings of these indications.This Dodge Journey dashboard warning lights guide also let you to go through the actions that should be implement when these warnings flickers. You can also refers the other models of Dodge on our site like Dodge Charger, Dodge Durango, Dodge Challenger and Dodge Ram Truck.
Dodge Journey ABS Warning Light
This dashboard symbol activates to indicate a malfunction in the Anti-lock braking System of your vehicle. In this scenario, you can still use your conventional parking brakes without the assistance of ABS. Later you have to inspect your car at Dodge service centre.
Dodge Journey Air Bag Warning Light
If this dashboard light flickers on your dashboard then it indicates a problem in the airbag system and it could not puff out in a crash or a hit. In this case, get serviced your airbag fault from nearby Dodge service centre.
Dodge Journey Battery Charge Warning Light
This warning light gets turn on when the battery is not adequately charged. If this light stays on for a long time, it indicates some malfunction in the charging system. Go and check your vehicle in the service centre.
Dodge Journey Brake Warning Light
This dashboard light gets active when the parking brake is applied or there is a fault in an anti-lock brake system, may be the brake fluid level is getting low in your vehicle. Suppose this light stays on for a longer time than it indicates that parking brakes are disengaged. So, release the parking brakes as earliest. And if this light is still on then go check your vehicle by Dodge service centre.
Dodge Journey Door Open Warning Light
This light gets activated when the Doors of your Dodge journey remain open and not closed properly.
Dodge Journey Electric Power Steering Fault Warning Light
This dashboard light activates when the electric power steering system is detecting a fault in it. If you continue your drive in this warning light, it can create a risk to your safety.
Dodge Journey Electronic Stability Control Active Warning Light
This dashboard light activates on your Dodge Journey Dashboard to indicates that the stability control system is activated in your car, and it is all set to assist you with the road grip and stability.
Dodge Journey Electronic Stability Control Off Warning Light
This warning symbol illuminates on your Dodge Journey dashboard to indicate that the Electronic stability control system is off in your vehicle. Now it will not assist you in controlling your car.
Dodge Journey Electronic Throttle Control Warning Light
This dashboard light gets activate when it indicates a problem in the electronic throttle control system. In this case, completely stop your vehicle and place it in a PARK position. If this light stays on for a long time, then it may reduce your vehicle performance.
Dodge Journey Engine Check Malfunction Indicator Warning Light
This light displayed on the Dodge Journey dashboard to indicates any malfunction in the engine. This light associates with the Automatic Transmission control system and engine monitoring of your vehicle. In this light, we highly advised you to contact dodge service centre.
Dodge Journey Engine Coolant Temperature Warning Light
This warning light activates to alert the driver that the engine of a vehicle is overheating. If this coolant temperature becomes high, then it indicates the chime sound. In this case, a driver should immediately stop the car and turn off the air-conditioning system. Shift your vehicle into the NEUTRAL transmission and idle the vehicle. Immediately switched OFF your system and called for service and maintenance.
Dodge Journey Engine Oil Pressure Light
If this warning light flickers on your Journey dashboard, then it indicates that your engine\'s oil pressure is getting lower. In this situation, please turn off the ignition and stop your vehicle to check its oil level. If the oil level is average, then you should contact to the Dodge service station as earliest.
Dodge Journey Front Fog Indicator Light
This dashboard light gets turn on when front fog lights are activate in your Dodge Journey.
Dodge Journey High Beam Indicator Light
This dashboard light activates when headlights are activated in your vehicle. In this case, push the malfunction lever forward to turn Off the high beams of your Dodge journey. If high beams are still ON, then pull the lever towards your direction to temporarily activate the high beam.
Dodge Journey Low Fuel Warning Light
This warning light indicates when your fuel level reaches 2.7 L, and It stays on until you add some fuel to your vehicle\'s fuel gauge.
Dodge Journey Low Washer Fluid Warning Light
This warning light gets activated when the washer fluid is getting low in your Dodge Journey.
Dodge Journey Park Headlight On Indicator Light
This warning light gets on when the headlights of your Dodge journey are activated.
Dodge Journey Seat Belt Reminder Warning Light
This dashboard light activates whenever the driver or any passenger\'s seat belt remains unbuckled. If this light remains on for a long time and continues to flash, then you should immediately check the seat belts of all the seats of your car.
Dodge Journey Speed Control Fault Warning Light
This dashboard light indicates when the cruise control system is all set to the desired speed.
Dodge Journey Tire Pressure Monitoring System(TPMS) Warning Light
This light activates along with a pop message on the dashboard that your vehicle\'s tire pressure is getting lower than the recommended values. Check all the tires by Dodge Service Station.
Dodge Journey Transmission Temperature Warning Light
This dodge journey dashboard light gets on to alert that the transmission fluid temperature is getting high. In this case, stop your vehicle and engine. Shift to the NEUTRAL position. When this light gets turned OFF, then you will continue driving.
Dodge Journey Turn Signal Indicator Light
This dashboard light gets turn on to alert the driver that your vehicle is driven more than one mile, or we can say 1.6 km with the turn signal on. This light flashes until the left, or right turn signal is activated.
Dodge Journey Vehicle Security Warning Light
This dashboard light activates on your Dodge Journey instrumental cluster when the vehicle security alarm is ringing, and it flashes slowly when the vehicle is disarmed.
Other Models
Porsche Taycan Dashboard Lights And Meaning
Audi Q5 Tire Pressure
Mitsubishi Lancer Dashboard Lights And Meaning
Ford Ranger Dashboard Lights And Meaning
Dodge Ram Truck Dashboard Lights And Meaning
Kia Niro EV Dashboard Lights And Meaning
Jeep Cherokee Dashboard Lights And Meaning
Fiat 500X Dashboard Lights And Meaning
Volvo XC40 Tire Pressure
GMC Acadia Tire Pressure
© 2023 warningsigns.net
- Fuel Consumption
- Engine Sizes
- Engine Torque
- Engine Power
- Towing Capacity
- Seating Capacity
- Steering Wheel Size
- Dimensions and Weight
- Fuel Tank Sizes
- Trunk Space
- Tire and Rim Sizes
- Bolt Patterns
- Coolers and radiators
- Radiator Fan
- Heat Exchanger
- Intercooler
- Timing Belt
- Sizes of Wiper Blades
- Cabin Filter
- Fuel Filter
- Transmission Fluid
- Antifreeze & Coolant
- Brake Discs
- Brake Drums
- Brake Fluid
- Bulbs For Fog Lights
- Bulbs For Headlights
- Bulbs For Turn Signals
- Bulbs For Licence Plates
- Bulbs For Markers
- Bulbs For Rear Fog Lights
- Bulbs For Backup Lights
- Bulbs For Brake Lights
- Technical Specs
- Car History
- Engine & Fuel
- Coolers and Radiators
Lightning Bolt on Dashboard in Dodge Journey - What’s This?
CarAraC auto mechanics and car experts
Your Dodge Journey has warning lights that illuminate on its dashboard , just like every other modern car. For example; the vehicle security warning, brake warning, airbag warning, battery warning, engine oil pressure warning, etc. Then there's the lightning alert that you may not be familiar with.
Lightning bolt warning lights highlights
- Common reasons: throttle control problems
- How to fix: disconnect the battery for some time, use scanner and get trouble codes
- Possible consequences: you may get stranded
- Priority level: High
- Can you drive? Carefully
- DIY repair: Impossible
- Repair price range: $150-$800
Brief Background to the Dodge Journey
Dodge Journey vehicles are medium-sized crossover SUVs (CUVs) that are issued by the Dodge brand. They were first released in 2009. Then there was a rebadge to the Fiat Freemont in 2011 as a parallel collection. The cars come in right-hand and left-hand drive.
The Dodge Journey comes with warning indicators just like other Dodge models. When these warning lights come up; it could be a system malfunction, security issue, or need for urgent maintenance.
Driver safety shouldn't be taken for granted, especially when a warning light comes on. Taking a related risk could be bad for you and/or the vehicle
What Is the Electronic Throttle Control on a Dodge Journey?
Your Dodge's electronic throttle control features an accelerator pedal module which has a motor, sensors, and a throttle plate. It's a great improvement from the traditional mechanical linkage in old-model cars. Although it isn't immune to mechanical faults.
The ETC measures the pressure drivers apply on the gas/accelerator pedal. The pedal isn't mechanically linked to the engine. A sensor tracks the pedal's position and the data is transmitted to the ETC for engine RPMs (revolutions per minute) to be adjusted.
Gas pedal pressure will determine how much the throttle passage will be opened. There's a flat valve at the opening that's regulated by the pedal's movement. It's called the throttle plate or butterfly valve.
The throttle plate rotates inside the throttle body when you depress the pedal. Then the air will be let into the intake manifold and quickly drawn into it by its vacuum.
1) Sensors in the ETC System
Two sensors that are instrumental to the ETC's operations include the following:
- Mass Airflow (MAF) Sensor
The mass airflow (MAF) sensor calculates the change in airflow. It will then send results to the engine's control unit (ECU) or electronic control module (ECM). This sensor is usually located between the throttle body and the air cleaner.
- Throttle position (TPS) Sensor or Throttle Valve Position Sensor
It's linked to the throttle body and it tracks your Dodge's throttle angle. You can find it on the reverse side of the throttle plate.
Don't get confused about the two sensors mentioned above. The TPS simply informs the ECU/ECM that you've depressed the gas pedal, while the MAF detects the air added. The NAF
2) The Role of the ECU
It's the ECU that controls the balancing of the air-fuel mixture in real-time. It also calculates the best moment to activate the spark plugs to ignite the balanced air-fuel combination.
3) Wide-Open Throttle (WOT)
This is what's referred to as full throttle. It's when the throttle is fully opened on an internal combustion engine or in your car. WOT also means the max-speed state of running an engine or the usual condition of a completely opened butterfly valve or throttle plate.
Your depression of the gas pedal in this situation is referred to as "flooring it". There'll be maximum intake of air because of the lowest resistance to incoming air.
What Does the Electronic Throttle Control Warning Light Mean?
The electronic throttle control warning light on your Dodge Journey could mean that the system has detected a communication problem that has resulted in an ETC error. It's most likely a result of a miscommunication between the ETC and its related sensors.
Dodge Journey vehicles were introduced almost a decade and a half ago, so the dashboard instrument cluster arrangement may vary based on the model year of your car. Still, the lightning symbol is very easy to notice when it illuminates.
Electronic Throttle Control Warning Light Behavior
The electronic throttle control warning light can be a troublesome alert that can come on at any time after the first illumination. And it can go off easily and come on after some days or even weeks. It may stay on for hours in some cases, only to stop when you restart the vehicle.
It will seem like the alert has a mind of its own. Worse still, the symptoms of the fault may not be easy to notice. The car might just be driving just fine regardless of the warning light. There's no need to get confused or nervous.
The ETC light could stay on after the initial indicator check when you first start your car. It could also activate when driving. Even the check engine light (CEL) could activate with it simultaneously.
What To Do Immediately After Noticing the ETC Warning Light
You could continue driving, but it wouldn't be the best move. Just remember to get the car checked at your earliest convenience if you decide to take the RISK.
Drivers could also stop the Dodge instead and park it at a convenient spot or put it in "park". Then proceed to put the engine off and cycle the ignition. The warning light may go off at this point.
Your car should be drivable if the alert doesn't go off. But the vehicle will need to be serviced ASAP. In case of the light flashing, then you should understand that the problem is a severe one that demands more urgency. It won't be advisable to drive the car in such a scenario, but you actually could.
Utilize a diagnostic scan tool to check for vehicle fault codes if you have one. This should be done before any other thing-be it DIY physical checks or hiring a professional technician. It may save you from getting scammed by the dealer or mechanic with a wrong diagnosis and unnecessary repair bills.
Ask the professional or dealer attending to you if they can let you be with them in the vehicle as the diagnoses are taking place. Some repairers offer such a service.
You'll have to take your car to the dealer or auto repair workshop immediately if you don't have a scan tool. Decreased engine power, rough engine noise, or abnormally high idle speed may be experienced if you drive the Dodge while the light is flashing.
Performance issues such as misfiring, stalling, and unstable throttle feedback when the light comes on while driving means you must stop the car. Towing the vehicle to a repairer is recommended at this point if you want to avoid complicating the situation.
Other Symptoms of a Bad ETC
You should look out for the following signs when the ETC alert comes on:
- Idle surges
- Rough idling
- Uninitiated acceleration (car accelerating by itself)
- Reduced fuel mileage (poor fuel economy)
- Engine misfiring
Electronic Throttle Control System Reset Procedure
The problem being indicated by the ETC light might just be the need for a gas pedal reset. The pedal position might not be well lined up or aligned. This will result in a communication error with the sensors that trigger the motor which closes or opens the throttle. Such could be the case in a high-mileage Dodge Journey.
Thankfully, the pedal reset can be done on your own instead of hiring a professional. Follow the steps below carefully to reset the pedal.
- Step 1: Switch on the ignition key without starting the vehicle.
- Step 2: Press the accelerator pedal to the floor and ease it up.
- Step 3: Start the vehicle and depress the pedal again. Observe whether your Dodge will respond or not. Check to see if the ETC light has gone off as well.
- Step 4: Proceed to drive the car around to see if the ETC is working well and if there are no other issues.
- Step 5: Take the car to a repair place if the throttle problem continues and the ETC light is still on.
Most of the warning lights that illuminate on your dashboard can't be taken for granted. And the Dodge Journey electronic throttle control warning light isn't an exception. That's why they're referred to as warnings. Always deal with the lightning symbol alert coming on as soon as possible.
Scanning your Dodge for diagnostic trouble codes (DTCS) will help in eliminating so many possibilities related to the ETC alert. It will save you from diagnostics bills at a repair shop or wasting money on "trial and error". You may only need to do a simple fix such as swapping out the air filter and ETC sensor, or resetting the pedal.
About the authors
The CarAraC research team is composed of seasoned auto mechanics and automotive industry professionals, including individuals with advanced degrees and certifications in their field. Our team members boast prestigious credentials, reflecting their extensive knowledge and skills. These qualifications include: IMI: Institute of the Motor Industry, ASE-Certified Master Automobile Technicians; Coventry University, Graduate of MA in Automotive Journalism; Politecnico di Torino, Italy, MS Automotive Engineering; Ss. Cyril and Methodius University in Skopje, Mechanical University in Skopje; TOC Automotive College; DHA Suffa University, Department of Mechanical Engineering
Add comment
Dodge RAM Warning Light Symbols and Meaning (FULL list, FREE Download)
If you’ve ever been surprised by an unexpected warning light on your Dodge RAM dashboard, you’re not alone!
I’m here to help!
In this guide, you’ll get comprehensive information about Dodge RAM warning light symbols with a full list of Dodge RAM dashboard lights and meanings in an image and an E-book (FREE Download).
Let’s take a look at my list!
Dodge RAM Warning Lights/Indicators and Meanings
Click the symbols for details if you want.
Electronic Throttle Control Warning Light
This warning light will illuminate to indicate a problem with the ETC system. If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position. The light should turn off. If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.
Air Bag Warning Light
This warning light will illuminate to indicate a fault with the airbag and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position. This light will illuminate with a single chime when a fault with the airbag has been detected, it will stay on until the fault is cleared. If the light is either not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
Vehicle Security Warning Light
This light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed.
Battery Charge Warning Light
This warning light will illuminate when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact an authorized dealer as soon as possible. This indicates a possible problem with the electrical system or a related component.
Seat Belt Reminder Warning Light
This warning light indicates when the driver or passenger seat belt is unbuckled. When the ignition is first placed in the ON/RUN or ACC/ON/RUN position and if the driver’s seat belt is unbuckled, a chime will sound and the light will turn on. When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound.
Brake Warning Light
This warning light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.
Engine Coolant Temperature Warning Light
This warning light warns of an overheated engine condition. If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound. If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool, whichever comes first. If the light turns on while driving, safely pull over and stop the vehicle. If the Air Conditioning (A/C) system is on, turn it off. Also, shift the transmission into NEUTRAL (N) and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service.
Oil Pressure Warning Light
This warning light will illuminate to indicate low engine oil pressure. If the light turns on while driving, stop the vehicle, shut off the engine as soon as possible, and contact an authorized dealer. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood.
Hood Open Warning Light
This warning light will illuminate when the hood is ajar/open and not fully closed.
Liftgate Open Warning Light
This warning light will illuminate when the liftgate is open.
Transmission Temperature Warning Light
This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmission into PARK (P) and run the engine at idle or slightly higher until the light turns off.
Oil Temperature Warning Light
This warning light will illuminate to indicate the engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Wait for oil temperature to return to normal levels.
Electric Power Steering Fault Warning Light
This warning light will turn on when there’s a fault with the EPS system
Trailer Brake Disconnected Warning Light
This warning light will illuminate when the Trailer Brake has been disconnected.
Door Open Warning Light
This indicator will illuminate when a door is ajar/open and not fully closed.
Engine Check Light
This warning light will illuminate when the ignition is in the ON/RUN position before the engine start. If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after the engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.
Electronic Stability Control Active Warning Light
This warning light will indicate when the ESC system is Active. The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, and when ESC is activated. It should go out with the engine running. If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected. ● The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position. ● The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive. ● This light will come on when the vehicle is in an ESC event.
Air Suspension Alternate Trailer Height
This light will illuminate when the air suspension system is set to the Alternate Trailer Height setting.
ESP BAS Light
This light indicates a problem with your car’s brake assist program or electronic stability system.
Electronic Park Brake Warning Light
This warning light will illuminate to indicate the Electronic Park Brake is not functioning properly and service is required. Contact an authorized dealer.
4WD High Indicator Light
This light alerts the driver that the vehicle is in the 4WD High mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.
Wait To Start Light
This indicator light will illuminate for approximately two seconds when the ignition is turned to the RUN position. Its duration may be longer based on colder operating conditions. Vehicle will not initiate start until telltale is no longer displayed.
Low Coolant Level Warning Light
This telltale will turn on to indicate the vehicle coolant level is low.
Loose Fuel Filler Cap Warning Light
This warning light will illuminate when the fuel filler cap is loose. Properly close the filler cap to disengage the light. If the light does not turn off, please see an authorized dealer.
Cold Ambient Derate Mode Indicator
This indicator light will illuminate when a derate (engine power reduction) is activated for protection of the turbocharger in cold ambient temperatures.
Electronic Stability Control OFF Warning Light
This warning light indicates the ESC is off. Each time the ignition is turned to ON/RUN or ACC/ON/RUN, the ESC system will be on, even if it was turned off previously.
Service LaneSense Warning Light
This warning light will illuminate when the LaneSense system is not operating and requires service. Please contact an authorized dealer.
Low Washer Fluid Warning Light
This warning light will illuminate when the windshield washer fluid is low.
Service Forward Collision Warning Light
This warning light will illuminate to indicate a fault in the FCW System. Contact an authorized dealer for service
Forward Collision Warning OFF Indicator
This indicator light illuminates to indicate that Forward Collision Warning is off.
Service Stop/Start System Warning Light
This warning light will illuminate when the Stop/Start system is not functioning properly and service is required. Contact an authorized dealer for service.
Tire Pressure Monitoring System Light
The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed. Should one or more tires be in the condition mentioned above, the display will show the indications corresponding to each tire. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires. As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life and may affect the vehicle’s handling and stopping ability.
Anti-Lock Brake System Light
This warning light monitors the ABS. The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible. However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on. If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer.
Rear Axle Locker Fault Indicator Light
This warning light will illuminate to indicate when a rear axle locker fault has been detected.
4WD Indicator Light
This light alerts the driver that the vehicle is in the four-wheel drive mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.
Water In Fuel Indicator Light
The “Water In Fuel Indicator Light” will illuminate when there is water detected in the fuel filter. If this light remains on, DO NOT start the vehicle before you drain the water from the fuel filter to prevent engine damage, and please see an authorized dealer.
Sway Bar Indicator Light
This indicator light will illuminate when the front sway bar is disconnected.
Service Adaptive Cruise Control Warning Light
This light will turn on when the Adaptive Cruise Control (ACC) is not operating and needs service.
Air Suspension Fault Warning Light
This light will illuminate when a fault is detected with the air suspension system.
Low Fuel Warning Light
When the fuel level is less than a ¼ tank, and the Distance to Empty is less than 50 miles, this light will turn on and remain on until fuel is added. A single warning chime will sound with Low Fuel Warning.
Speed Control Fault Warning Light
This warning light will illuminate to indicate the Speed Control System is not functioning properly and service is required. Contact an authorized dealer.
Trailer Merge Assist Indicator Light
This indicator light will illuminate to indicate when Trailer Merge Assist has been activated.
TOW/HAUL Indicator Light
This indicator light will illuminate when TOW/HAUL mode is selected.
Cargo Light
This indicator light will illuminate when the cargo light is activated by pushing the cargo light button on the headlight switch.
Front And Rear Axle Lock Indicator Light
This light indicates when the front, rear, or both axles have been locked. The telltale will display the lock icon on the front and rear axles to indicate the current lock status.
Rear Axle Lock Indicator Light
This light indicates when the rear axle lock has been activated.
Service 4WD Warning Light
This warning light will illuminate to signal a fault with the 4WD system. If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required. We recommend you drive to the nearest service center and have the vehicle serviced immediately.
4WD Low Indicator Light
This light alerts the driver that the vehicle is in the 4WD Low mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels.
NEUTRAL Indicator Light
This light alerts the driver that the 4WD power transfer case is in the NEUTRAL mode and the front and rear driveshafts are disengaged from the powertrain.
Low Diesel Exhaust Fluid Indicator
The indicator will illuminate if the Diesel Exhaust Fluid (DEF) level is low.
Diesel Exhaust Brake Indicator Light
This indicator light will illuminate when the Diesel Exhaust Brake has been activated, and is in full strength mode.
Sway Bar Fault Warning Light
This light will illuminate when there is a fault in the sway bar disconnect system.
Snowplow Mode Indicator Light
This indicator light will illuminate when Snowplow Mode has been activated.
Air Suspension Payload Protection Light
This indicator light will illuminate to indicate that the maximum payload may have been exceeded or load leveling cannot be achieved at its current ride height. Protection Mode will automatically be selected to “protect” the air suspension system, air suspension adjustment is limited due to payload.
Air Suspension Bed Lowering Mode
This light will illuminate when the Bed Lowering Mode procedure is complete.
Air Suspension Ride Height Raising
This light will blink and alert the driver that the vehicle is changing to a higher ride height.
Air Suspension Ride Height Lowering
This light will blink and alert the driver that the vehicle is changing to a lower ride height.
Adaptive Cruise Control Light
This light will turn on when the ACC is SET and there is no target vehicle detected.
LaneSense Indicator Light
The LaneSense indicator light illuminates solid green when both lane markings have been detected and the system is “armed” and ready to provide visual and torque warnings if an unintentional lane departure occurs.
This will display when the ACC is set and a target vehicle is detected.
ECO Mode Indicator Light
This light will turn on when ECO Mode is active.
Park/Headlight On Indicator Light
This indicator light will illuminate when the park lights or headlights are turned on.
Front Fog Indicator Light
This indicator light will illuminate when the front fog lights are on.
Turn Signal Indicator Lights
When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash. Turn signals can be activated when the multifunction lever is moved down (left) or up (right).
Speed Control SET Indicator Light
This light will turn on when the speed control is set.
Stop/Start Active Indicator Light
This indicator light will illuminate when the Stop/Start function is in “Autostop” mode.
4WD AUTO Indicator Light
This light alerts the driver that the vehicle is in the four-wheel drive auto mode, and the front axle is engaged, but the vehicle’s power is sent to the rear wheels. Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction.
Automatic Diesel Exhaust Brake Light
This indicator light will illuminate when the Diesel Exhaust Brake has been activated, and has switched to Automatic mode.
Cruise Control Ready Indicator
This indicator light will illuminate when the cruise control is ready, but not set.
Adaptive Cruise Control Ready Light
This light will illuminate when the vehicle equipped with ACC has been turned on but not set.
Cruise Control SET Indicator Light
This light will turn on when the cruise control is set.
Hill Descent Control Light
This indicator shows when the HDC feature is turned on. The lamp will be on solid when HDC is armed. HDC can only be armed when the transfer case is in the “4WD LOW” position and the vehicle speed is less than 20 mph (32 km/h). If these conditions are not met while attempting to use the HDC feature, the HDC indicator light will flash on/off.
When the LaneSense system is ON, but not armed, the LaneSense indicator light illuminates solid white. This occurs when only left, right, or neither lane line has been detected. If a single lane line is detected, the system is ready to provide only visual warnings if an unintentional lane departure occurs on the detected lane line.
High Beam Indicator Light
This indicator light will illuminate to indicate that the high-beam headlights are on. With the low beams activated, push the multifunction lever forward (toward the front of the vehicle) to turn on the high beams. Pull the multifunction lever rearward (toward the rear of the vehicle) to turn off the high beams. If the high beams are off, pull the lever toward you for a temporary high beam on, “flash to pass” scenario.
Now you know what your car is trying to tell you and have a better understanding of Dodge RAM dashboard lights.
But it can be challenging to remember exactly the name and meaning of each symbol, right?
No problem!
I’ve compiled the full list of Dodge RAM warning lights and indicators with their meanings in an image and a PDF E-book for you.
Don’t hesitate to download them for later use!
DODGE RAM WARNING LIGHTS AND INDICATORS
Get access to my full list of these dashboard lights and become a better driver.
What’s Next?
To maintain the performance and safety of your Dodge RAM vehicle, pay attention to any warning lights that may appear on your dashboard.
Remember, when the red or yellow symbols light up, take your car to a mechanic, or buy a scan tool to self-check.
Don’t miss my review on Best Chrysler/Jeep/RAM Scan Tools to find the right tool for you.
FOXWELL NT510
Worried about your Mini Cooper? Check out my complete guide to Mini Cooper Warning Lights .
Share this article
Related Posts
Restraint system warning lamp, seat belt warning lamp, 1 thought on “dodge ram warning light symbols and meaning (full list, free download)”.
Leave a Comment Cancel Reply
Your email address will not be published. Required fields are marked *
Save my name, email, and website in this browser for the next time I comment.
Recommended for you
Volvo Dashboard Symbols and Meanings
Kenworth Dashboard Lights and Meanings
Freightliner Warning Lights and Meanings
Start typing and press enter to search.
Dodge Journey Check Engine Light On: Why and What to Do
The check engine is the most common warning light that appears in the Dodge Journey’s instrument cluster. Well over half of this site’s content is related to solving the various reasons why the check engine light comes on.
The good news is that the check engine light indicates that there are Diagnostic Trouble Codes (DTCs) stored in your Journey’s computer , which is a very good thing. DTC’s really help save time determining what is wrong with your vehicle.
The check engine light is often referred to as the Malfunction Indicator Lamp (MIL) or Service Engine Soon light. All three terms are 100% interchangeable.
Table of Contents
- What Are Trouble Codes ?
- How to Pull Trouble Codes
How to Reset the Check Engine Light
Common questions, what are trouble codes.
Trouble codes are a number sequence of letters and numbers that correspond with a standardized list of problems that can occur in any vehicle, including the Dodge Journey . Some of them are Dodge specific, while most have the same meaning no matter who made the vehicle.
Common OBD II Codes
The most common of all trouble codes is P0420 (it indicates your Dodge Journey’s catalytic converter isn’t scrubbing pollutants efficiently).
Here are some of the other most common codes:
- P0442 – Small EVAP leak (most commonly fixed by tightening a loose gas cap or replacing it)
- P0300 – Random misfire (bad ignition coil(s), spark plugs, or spark plug wires).
- P0128 – Engine running too cool (almost always caused by a thermostat that’s stuck open)
- P0172 – Air Fuel mixture too rich (there are many causes, including oxygen sensors, leaking injectors, or too much fuel pressure)
The most common codes are related to the emissions system . Some of them are as easy to fix as replacing your Journey’s. Others require serious diagnostic tests from a repair shop.
How to Pull Trouble Codes on the Dodge Journey
You can either pull the trouble codes from your Journey’s PCM (Powertrain Control Module) yourself, or you can bring your vehicle to a parts store or shop to have it scanned.
Pull Them Yourself
You can put a scan tool into the OBD II port and pull codes out of the diagnostic system yourself. Any vehicle made for the 1996 model year and up uses the same protocol.
You can usually find the OBD II port underneath the Journey’s steering wheel. The exact location of the port is going to depend on what model year you have. If you don’t see it check the owner’s manual or do a quick google image search.
Once your scanner is online, you can pull the codes. You should see a retrieve codes option.
Take Your Carortruck to a Shop or Parts Store
If you don’t have a scan tool, you can take your Journey to the local parts store. Most of them are happy to pull the codes for you for free .
A lot of auto shops also offer free scan service, but you may find pressured into authorizing whatever repairs they suggest on the spot.
Once you have the codes in hand, you can look them up and determine what’s wrong with your Journey.
There are three ways to reset the Dodge Journey’s check engine light. We recommend trying to identify the problem and fixing it before resetting the check engine light.
1. Fix and Wait
The best way to clear the check engine light is to pull the trouble code, identify and fix the issue and then drive your Journey around until the module that threw the code recognizes that the problem is fixed.
Sometimes it can take a few drive cycles for your vehicle’s check engine light to shut down. Other times, it’ll happen as soon as you fire the vehicle up. Some folks prefer to clear the code and see if it comes back on
2. Use an OBDII Scanner
You can use an OBDII scanner to turn off your Journey’s check engine light. The catch is, that if you don’t fix the problem, the light will turn on again.
This is done by connecting a scan tool to your Journey’s PCM and choosing the “clear codes” option.
Once you’ve identified and fixed the issue, wait for three or four days of normal driving to see if the Check Engine Light turns back on.
If it does not come back on after this period, then you can assume that your Dodge Journey is fixed and the light won’t be turning back on.
3. Disconnect the Battery
If you’ve identified and fixed the issue that caused your Journey’s Check Engine Light to come on, resetting the light is as simple as disconnecting and reconnecting the battery. This can be done by unhooking both cables from the battery terminals (negative cable first) and waiting 30 seconds before reconnecting them.
Once the battery is reconnected, your Check Engine Light should be reset and should no longer be illuminated. If the light does come back on again after you reset it, then it means that the issue has not been properly fixed and needs further attention.
Will a Vehicle Fail Inspection With the Check Engine Light On
If you are looking to get your Dodge Journey through emissions and the check engine light is on, it is an automatic fail in almost every State in the Union. It doesn’t matter why the check engine light is on, it only matters that a code is stored.
Here’s a list of the emissions regulations of each State .
You can’t reset a check engine light to circumvent emissions requirements. When you reconnect the battery, the OBD II system is going to need several drive cycles to qualify to take an emissions test, which will give it enough time to recognize the issue.
Can You Drive With the Check Engine Light On?
Whether you can drive your Journey with the check engine light on depends on the code(s) that triggered the check engine light.
You certainly can’t drive the Dodge Journey with the check engine light flashing. A flashing check engine light indicates that there is a serious problem with the engine.
Why is My Check Engine Light Flashing?
A flashing Check Engine Light typically indicates a serious issue with your Journey and should not be ignored. It usually indicates a catastrophic misfire that can dump raw fuel into the exhaust system, which can damage the catalytic converter and cause backfiring. Do not drive your vehicle with a flashing check engine light .
Home » Troubleshooting » Dodge Journey dashboard lights flicker and won’t start – causes and how to fix it
Dodge Journey dashboard lights flicker and won’t start – causes and how to fix it
Flickering dashboard lights in Dodge Journey when attempting to start the engine might seem like a major malfunction has occurred, but in the majority of cases it’s not a serious cause for concern.
The most common causes for flickering dashboard lights and no engine crank in Dodge Journey are weak battery, corrosion on battery terminals, and bad ground connection.
1. Weak battery
The leading cause of flickering dashboard lights and no start in Dodge Journey is weak battery. You may also hear rapid clicking noise when you try to start the engine. If there isn’t enough charge in the battery to power the starter motor, and you try to crank the engine, the battery voltage will get so low that it can’t properly power the lights, accessories and of-course the starter.
Symptom: Rapid clicking sound
How to test the battery in journey.
The easiest method to check the 12v battery in Journey is by measuring the voltage with a multimeter. A healthy battery should have 12.6 volts or more when fully charged. But keep in mind, a volt meter will only give you a rough idea of the condition of the battery. Sometimes a battery showing over 12.4 volts may not be able to supply enough current to crank the engine.
Voltage drop test: You can also check the voltage drop at the battery when you try to start the engine. If the voltage drops too much, below 10 volts, your battery doesn’t have enough charge to start the engine. This can happen due to internal degradation of the battery, if the vehicle has been sitting for a long time, or if the alternator in your Journey has malfunctioned and not charging the battery properly.
How to jump start Journey
To rule out dead battery, your best course of action is to jump start your Journey using jumper cables and a healthy battery from another vehicle, or using a battery booster if available. Requirements: The engine of both the vehicles should be off, and the transmission in Park.
- Connect the red cable to the positive terminal of the dead battery in Journey.
- Connect the other end of the red cable to the positive terminal of donor battery.
- Connect the black cable to the negative terminal of donor battery.
- Finally connect the other end of the black cable to any bare unpainted metal part of the body or engine of your Journey. Safety warning: Connecting black cable directly to the negative terminal of Journey battery can ignite flammable gases from the battery due to sparks.
- Start your Journey.
- Remove the cables in the reverse order.
Warning: There is always a risk of burning up the alternator or other electrical components if the engine of the donor battery vehicle is running during jump start. Therefore it is recommended to keep the engine of the donor vehicle off when jump starting your Journey.
Recommended video
2. Poor battery connection
It is possible the battery in your Dodge Journey is in good health, but the current flow is interrupted due to loose electrical connection, damaged wire, or corrosion on the battery terminals.
Corrosion on battery terminals
Battery corrosion is a fairy common problem, especially if the installed battery is more than 2 years old. Corrosion occurs when the battery acid reacts with the metal terminals which can lead to loss of contact and reduced current flow. If there isn’t enough current flow to crank the engine, the dashboard lights may flicker and you may also hear clicking noise from the starter solenoid when you try to start the engine.
Check battery terminals
To know if your Journey starting problems are from dirty battery terminals, you need to investigate them. Lift the plastic covers over the terminals and check for any signs of corrosion. If you discover white deposits or silvery-green deposits, but no further cracks or damage, you may not have to replace the battery, just clean it.
Clean the battery terminals
Quick cleaning: There is a neat little trick with which you can clean corrosion on the battery terminals of your Journey in under a minute. Pour hot boiling water over the corroded terminals and the corrosion will just melt away. Do one terminal at a time and don’t let water puddle on the top of the battery touch both terminals at the same time, this can short the battery.
Thorough cleaning: To thoroughly clean the battery in your Dodge Journey, you have to remove the terminal cables first, which requires no special knowledge, just a little concentration, as the order is very important. First remove the black cable from the negative terminal using a wrench or a plier. Next you can unplug the red positive terminal cable. Be careful not to touch both terminals with your metal tool, it will be one expensive mistake. Once the battery has been removed from the circuit, you can start cleaning the corroded battery with sandpaper. After cleaning, reconnect the cables in reverse order, positive first, then negative.
3. Bad ground connection
What is a ground connection.
The negative terminal of the battery is connected to the body/chassis of Journey, called a ground connection. The engine also requires a ground connection to function, but the way the engine is mounted, it does not allow the electric current to flow between the engine and the body (due to non-conductive rubber insulated engine mounts). For this purpose, a ground strap/wire is used to connect the engine and the chassis.
What happens when the ground connection goes bad?
If the ground connection of the chassis or the engine goes bad in your Journey due to rust or corrosion, you will face all sorts of electrical issues, including clicking noises, flickering dashboard lights, and no start problem. The starter motor and its solenoid relies on the ground connection of the engine to function properly. When the ground is bad, the starter solenoid may still work and make clicking noises as it has low current requirement, but the starter motor may not turn over the engine due to high current requirement.
How to check if the ground connection is good?
You can check the quality of the ground connection in Journey by doing a conductivity test between the negative terminal of the battery and the chassis/body of the vehicle and the engine. Take a multimeter, change its settings to ohms symbol. Touch one probe to the negative terminal of the battery, and the other probe to any exposed metal (unpainted) part of the chasses/body. The reading should be at or very close to zero ohms. Do the same between the negative terminal of the battery and any exposed metal part of the engine.
Inspect the ground connections
If the conductivity test fails, check the condition of the ground connections in your Journey. Inspect the connectors of the ground cables (battery to body, body to engine) for any signs of rust or corrosion. Clean the contacts with a sandpaper.
There are many reasons why your Dodge Journey dashboard lights flicker and won’t start. When looking for the reason, you should start with the most obvious causes that are easy to diagnose: weak battery, and poor electrical connection.
In any case, it is advisable for laypersons to visit a workshop. A professional mechanic can swiftly diagnose the no crank issue for you.
- Chevy Camaro bad wheel bearings symptoms, causes and diagnosis
- Nissan Titan makes sloshing water sound – causes and how to fix it
- Audi A7 clogged catalytic converter symptoms, causes, and diagnosis
- Buick Envision AC not cooling – causes and diagnosis
- Maserati GranTurismo AC smells bad – causes and diagnosis
- Audi S6 Android Auto not working – causes and how to fix it
- Toyota Matrix low oil pressure light is on – causes and how to reset
- Ford F-350 Super Duty auto windows not working, how to reset
- Acura MDX Bluetooth not working – causes and how to fix it
- Renault Megane airbag light is on – causes and how to reset
- Ferrari California T bad wheel speed sensor symptoms – how to diagnose
- Porsche 911 windshield washer not working – causes and how to fix it
- Aston Martin DB11 heater not working – causes and diagnosis
- Volvo XC90 makes clicking noise and won’t start – causes and how to fix it
- Lincoln MKX bad mass air flow sensor (MAF) symptoms and causes
- How to connect two phones in Jeep Grand Cherokee
- BMW 7 Series heater not working – causes and diagnosis
- BMW Z4 bad wheel bearings symptoms, causes and diagnosis
- Chevy Trax bad wheel speed sensor symptoms – how to diagnose
- Ford Excursion bad alternator symptoms, how to check voltage
- Remember me Not recommended on shared computers
Forgot your password?
- Engine & Transmission
ABS, traction and service AWD light on
By sidney john April 18, 2016 in Engine & Transmission
- Reply to this topic
- Start new topic
Recommended Posts
Sidney john.
Hi everyone.. need help here please..i have a dodge journey 2012 with 71k milleage unfortunately my wheel bearing driver side give up and i change it by myself, after installing the new bearing and have it for drive check suddenly the 3 lights warning went on (ABS, TRACTION CONTROL,SERVICE AWD) i dont know what i did wrong..please anybody has a similar issue like mine that can help me determine the problem..thanks in advance
Link to comment
Share on other sites.
If you did not plug in the sensor properly, the car will have no idea at what rate each wheel is turning. Hence, no AWD, ABS, TC and I'll bet that your Cruise will not work either.
- 2late4u and John/Horace
yes i did, was install properly thats why i can't figure out whats the cause of lights on on my dash
Unplug the sensor, and make sure you did not bend a pin. They are touchy. Then disconnect the negative terminal of your battery for about 30 minutes to reset your system. See what happens.
- 2late4u , OhareFred and sidney john
- 1 year later...
Shawn Patrick Smith
On 4/18/2016 at 12:49 PM, sidney john said: yes i did, was install properly thats why i can't figure out whats the cause of lights on on my dash
I have these lights on my dash. I am not sure whats going on but the car has been running fine since I got the car in 2016 brand new. the light s came on yesterday when I went to go out, thinking it was because of the snow and ice build up in the wheel well I cleared that out and tried shutting down and restarting the car, lights went out. went to go out last night and they came on, so I stopped shut it off and started lights went out then came on after I drove a little bit. went home instead of testing the limits. came out to snow blow the drive way, started car only 2 lights ABS and TC came on. moved the car to the street and light s went out. went to go fill the car up with gas and because the street hasn't been plowed yet, theres still quite a bit of snow on the street so when the traction control kicked in car lost some power and then the 3 lights came on again, awd no abs and when the tc light comes on it loses power unless I turn the TC off and only the front wheels spin. because of the holidays the dealer ship is closed. does anyone know if this would be safe to drive until I get it into service?
I would take a picture of your dash showing the light s so when you take it the dealer you can show them what it is doing
Yes it is safe to drive.
- 2 years later...
Ziyad thaher
I have the same problem. Did you fix it? How?
- 2 months later...
Did anyone fix this for knows how?
John/Horace
Scan for codes to figure out which abs wheel sensor is bad. Then replace sensor and reset with scanner.
- jkeaton , 2late4u and Summer Solstice
What he said ^^^^
On 4/17/2016 at 9:01 PM, sidney john said: Hi everyone.. need help here please..i have a dodge journey 2012 with 71k milleage unfortunately my wheel bearing driver side give up and i change it by myself, after installing the new bearing and have it for drive check suddenly the 3 lights warning went on (ABS, TRACTION CONTROL,SERVICE AWD) i dont know what i did wrong..please anybody has a similar issue like mine that can help me determine the problem..thanks in advance
I know you probably have fixed your problem but this just happened to me for no reason. All systems seemed go so before I connected my OBD reader I tried the trick used for resetting the oil change reminder. Turned the car to run, but do not start it, pressed the accelerator pedal three times holding it down for one second each time. Turned the car off and then restarted it and the trouble codes went away and the cruise control started working. It did not happen again. I am assuming there was something on the sensor and it threw the code when we first started the car. Until reset it stayed on. Once reset it did not return. Just a shot in the dark for you. I got lucky.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account. Note: Your post will require moderator approval before it will be visible.
× Pasted as rich text. Paste as plain text instead
Only 75 emoji are allowed.
× Your link has been automatically embedded. Display as a link instead
× Your previous content has been restored. Clear editor
× You cannot paste images directly. Upload or insert images from URL.
- Insert image from URL
- Submit Reply
- Existing user? Sign In
More Forum Apps
- Online Users
- Leaderboard
|| Forum Activity ||
- All Activity
- Create New...
- Lights & Lighting Accessories
- Lighting Assemblies & Accessories
- Brake & Tail Light Assemblies, Parts & Accessories
- Tail Light Assemblies
Enjoy fast, free delivery, exclusive deals, and award-winning movies & TV shows with Prime Try Prime and start saving today with fast, free delivery
Amazon Prime includes:
Fast, FREE Delivery is available to Prime members. To join, select "Try Amazon Prime and start saving today with Fast, FREE Delivery" below the Add to Cart button.
- Cardmembers earn 5% Back at Amazon.com with a Prime Credit Card.
- Unlimited Free Two-Day Delivery
- Streaming of thousands of movies and TV shows with limited ads on Prime Video.
- A Kindle book to borrow for free each month - with no due dates
- Listen to over 2 million songs and hundreds of playlists
- Unlimited photo storage with anywhere access
Important: Your credit card will NOT be charged when you start your free trial or if you cancel during the trial period. If you're happy with Amazon Prime, do nothing. At the end of the free trial, your membership will automatically upgrade to a monthly membership.
Return this item for free
Free returns are available for the shipping address you chose. You can return the item for any reason in new and unused condition: no shipping charges
- Go to your orders and start the return
- Select the return method
This item has been tested to certify it can ship safely in its original box or bag to avoid unnecessary packaging. Since 2015, we have reduced the weight of outbound packaging per shipment by 41% on average, that’s over 2 million tons of packaging material.
Image Unavailable
- To view this video download Flash Player
LED Inner Tail Light Lamp Stop Brake Indicator Warning Light For Dodge Journey 2012 2013 2014 2015 2016 2017 2018 with Bulb (Right Passenger Side)
Purchase options and add-ons, about this item.
- 🚗Meets or exceeds DOT/SAE standards, with particular consideration for photo metric and safety compliance.Waterproof and shock resistant. no modification necessary, plug and play, install is easy.Meets or exceeds DOT/SAE standards, with particular consideration for photo metric and safety compliance.Waterproof and shock resistant. no modificatio necessary, plug and play, install is easy.
- 🚗Special coating on the lens surface prevents hazing and fading, ensuring proper illumination and operational safety.Rigorous and accelerated cycling tests to ensure product service quality and durability.
- 🚗Package Included: 1 PC Tail Light (Right Passenger Side)
- 📧Each Of Our Products Is Elaborately Designed And Manufactured,We Have A Strict Quality Control System To Ensure A Stable Quality. If you have any questions, please feel free to contact us, we will get back to you within 24 hours.
Buy it with
Similar items that may deliver to you quickly
From the brand
Our was established in 2019, is a professional supplier engaged in the research, development, sale of car accessories.
In recent years, our company has introduced a series of products. The products are designed, manufactured, tested by our R&D team and passed variousCertification.
Whether selecting a current product from our catalog or seeking professional assistance for your application, you can talk to our about your sourcing requirements.
MZORANGE Tail Light Lamp
Product Description
About tail light.
- If you are looking for exquisite and outstanding For Dodge Journey tail light, then this set of excellent For Dodge Journey warning light is your ideal choice.
Detailed introduction
- For Dodge Journey 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018
- Durable ABS plastic body,meets or exceeds DOT/SAE standards.
- Please make sure this item fits for your vehicle before you purchase.
- OMG:4806369AF, 4806368AF
- For easy install
- Light bulb is included
- Before you begin installation, please inspect the tail light of damage. Do not install them if there is any damage.
- Please make sure that the tail light are firmly installed before driving.
Product information
Technical details, additional information, warranty & support, compare with similar items, looking for specific info, customer reviews.
Customer Reviews, including Product Star Ratings help customers to learn more about the product and decide whether it is the right product for them.
To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzed reviews to verify trustworthiness.
Reviews with images
- Sort reviews by Top reviews Most recent Top reviews
Top reviews from the United States
There was a problem filtering reviews right now. please try again later..
Top reviews from other countries
- Amazon Newsletter
- About Amazon
- Accessibility
- Sustainability
- Press Center
- Investor Relations
- Amazon Devices
- Amazon Science
- Start Selling with Amazon
- Sell apps on Amazon
- Supply to Amazon
- Protect & Build Your Brand
- Become an Affiliate
- Become a Delivery Driver
- Start a Package Delivery Business
- Advertise Your Products
- Self-Publish with Us
- Host an Amazon Hub
- › See More Ways to Make Money
- Amazon Visa
- Amazon Store Card
- Amazon Secured Card
- Amazon Business Card
- Shop with Points
- Credit Card Marketplace
- Reload Your Balance
- Amazon Currency Converter
- Your Account
- Your Orders
- Shipping Rates & Policies
- Amazon Prime
- Returns & Replacements
- Manage Your Content and Devices
- Recalls and Product Safety Alerts
- Conditions of Use
- Privacy Notice
- Consumer Health Data Privacy Disclosure
- Your Ads Privacy Choices
Dodge Gas Cap Warning Light to Come On - How To Fix It?
The gas cap warning light on your Dodge car is designed to notify you when the fuel tank cap is not tight. When the Dodge gas cap warning light comes on, it means that there is a small leak in the system and that vapors are escaping . A few things can cause this light to come on, and we’ll explore those in this article. We’ll also show you how to reset the morning if it does come on.
⚡️ Another article: Dodge AWD Warning Light
What is the Dodge Gas Cap Warning Light?
The Dodge gas cap warning light visually indicates that the gas cap is not closed correctly . If the light comes on, it means either the gas cap is not fully tightened, or there is a problem with the pressure sensor in the fuel system.
Pulling over and checking the gas cap is essential if the light comes on while driving. Make sure that it is tight before continuing to navigate. If the light comes on and stays on after restarting the engine, there may be a problem with the pressure sensor, which will need to be checked by a mechanic .
⚡️ Another article: What is Dodge Cummins P0868 Code Mean?
What Causes the Dodge Gas Cap Warning Light to Come On?
There are a few reasons why a Dodge vehicle's gas cap warning light may come on. If the light is flashing, the gas cap is not tightened correctly. This can cause the engine to run inefficiently and damage the catalytic converter. If the light is solid, the fuel tank pressure is too low. This could be caused by a leak in the fuel system or a problem with the evaporative emission control system .
How to Fix the Dodge Gas Cap Warning Light?
If your Dodge gas cap warning light is on, it's important to take action to fix the problem. The most likely cause of the warning light is a loose or damaged gas cap.
To fix a loose gas cap, tighten it until it clicks. If the gas cap is damaged, you must replace it with a new one .
Once you've fixed the problem, the Dodge gas cap warning light should turn off. If it doesn't, another issue with your vehicle may need to be addressed.
The Dodge gas cap warning light is a feature that is designed to help drivers know when the gas cap is not closed properly. While it may seem minor, tightening the gas cap can help improve fuel economy and prevent environmental damage. If you see the Dodge gas cap warning light, check the gas cap and pull it if necessary.
🚨You may be interested in: Warning Lights In Dodge Caravan
FAQs About Dodge Gas Cap Warning Light
Why does my dodge ram say to check the fuel cap.
When the Check Fuel Cap light illuminates, it could indicate that the gas cap is not secured correctly. This may occur even if the cap is in place on the tank. To ensure that this issue does not persist, it is essential to ensure the fuel cap has been firmly fastened before proceeding any further.
Why won't my gas cap light go off?
It is easy to identify if the gas cap needs replacing by checking whether the light keeps coming on and going off again once it is tightened. If this is the case, a replacement gas cap should be ordered.
Why does my car keep saying to check the fuel cap?
The Check Fuel Cap Light comes on in the dashboard when the fuel cap has not been adequately affixed to the fuel tank filler tube, is missing from the fuel tank filler tube, or is damaged somehow. Addressing these potential problems immediately is essential to avoid further damage or safety-related issues.
Was this page helpful?
More important content about Dodge
Code P1693 on Dodge Cummins: Turbo Charge Control Circuit Malfunction
Dodge dakota years to avoid, warning lights in dodge caravan, dodge charger years to avoid - 6 worst years, dodge avenger dashboard warning lights and symbols.
I recently had a problem with my Dodge's gas cap. It was really frustrating because I could not open it and fill up at the pump. I ended up going to a mechanic and they were able to fix it for me quickly. Now, everything is back in working order and I am very glad that I didn't have to spend too much money on the repair.
Leave a Comment Cancel reply
Save my name, email, and website in this browser for the next time I comment.
Tips and Advice
Cummins ISX Years To Avoid and Why
Car with key symbol on dashboard, electronic throttle control warning light on - why, how many lamborghinis are there in the world - 2023 data, why are all the dashboard lights on in my car, pennzoil vs. mobil 1 comparison: which motor oil is better.
Russian City Freezes After Electricity Fails
A power outage in Russia's Siberia region left almost half of the city of Omsk without power amid subzero temperatures.
Vladimir Shnipko, Omsk's minister of energy and housing and communal services said there was an emergency shutdown at the Tavricheskaya substation. On Wednesday at around 5 p.m. local time, the lights suddenly went out in several areas of Omsk, including in both central regions of the city, and in rural areas, local media reported.
There have been large-scale power outages nationwide since the new year, leaving Russians to grapple with freezing temperatures as authorities work to restore heat to homes. Power outages have also struck St. Petersburg, Rostov, Volgograd, Voronezh, Primorsky Territory, Yekaterinburg and Novosibirsk in Siberia.
Omsk's regional governor, Vitaly Khotsenko, said that power has been restored in the Lyubinsky, Sargatsky, Tarsky and Ust-Ishimsky municipal districts of the region. "Energy workers continue to work," he said.
Local authorities were cited by Russia's state-run news agency as saying that most consumers who received electricity from the Tavricheskaya substation had their power restored within 30 minutes.
"The power supply to consumers of the 500 kV Tavricheskaya substation was completely restored in less than two hours. Most of it was powered within half an hour. The emergency automatics were activated at the substation. There was no damage to the equipment of the power facility," the news agency was told.
Anton Gerashchenko, an adviser to Ukraine's minister of internal affairs, shared a video on X, formerly Twitter , purportedly showing Omsk in darkness amid the power outage.
"Russians are ready to freeze without electricity and heat but continue supporting Putin and the 'special military operation'," he wrote, referring to the Kremlin's term for its ongoing war in Ukraine.
Newsweek has contacted Russia's foreign ministry for comment by email.
Elsewhere, approximately 25 percent of Moscow region was affected by power outages this week after a heating main burst at the Klimovsk Specialized Ammunition Plant in the town of Podolsk, which is around 30 miles south of central Moscow on January.
Affected areas included the cities of Khimki, Balashikha, Lobnya, Lyubertsy, Chekhov, Naro-Fominsk, and Podolsk, a map published by a Russian Telegram channel and shared on other social media sites showed.
Other Russian media outlets reported that in Moscow, residents of Balashikha, Elektrostal, Solnechnogorsk, Dmitrov, Domodedovo, Troitsk, Taldom, Orekhovo-Zuyevo, Krasnogorsk, Pushkino, Ramenskoye, Voskresensk, Losino-Petrovsky, and Selyatino are also without power.
Do you have a tip on a world news story that Newsweek should be covering? Do you have a question about the Russia-Ukraine war? Let us know via [email protected].
Related Articles
- Russian Doctor Gives Putin Surprise Diagnosis
- Saboteurs Who Poisoned 46 Russian Soldiers on the Run in Crimea: Report
- Russians' Stark 'Armed Insurrection' Warning Amid Mobilization Backlash
Start your unlimited Newsweek trial
Lobnya, Moscow
Around the globe, hurricane tracker.
Severe Weather
Radar & Maps
News & features, today's weather.
Low clouds; a bit of snow this morning with little or no accumulation followed by a shower in spots this afternoon Hi: 46°
Tonight: Low clouds, then perhaps some clearing Lo: 40°
Current Weather
Looking ahead.
Mild Sunday
Lobnya Weather Radar & Maps
Hourly Weather
10-day weather forecast.
A bit of snow this morning
Night: Mainly cloudy
Cloudy and milder
Clouds breaking; mild
Remaining cloudy and warm
A couple of evening showers
High clouds and warm
Partly cloudy and mild
Partly sunny and warmer
Mild with patchy clouds
Partly sunny and pleasant
Partly cloudy
Increasing cloudiness
Mostly cloudy
Cooler with low clouds
Clear and colder
Mostly sunny
Becoming cloudy
A little rain early; clearing
Sun & Moon
Air quality.
The air quality is generally acceptable for most individuals. However, sensitive groups may experience minor to moderate symptoms from long-term exposure.
Allergy Outlook
Top Stories
Weather News
Aftershocks rattle Northeast after rare 4.8 magnitude earthquake
3 hours ago
Weather Forecasts
Short burst of mild weather in the Northeast; rain to return midweek
58 minutes ago
Solar Eclipse 2024
Severe thunderstorms threaten eclipse travelers in Southern Plains
34 minutes ago
Dozens rescued after major Taiwan quake, more than 600 still cut off
Winds to howl, snow to fly over Rockies and High Plains this weekend
46 minutes ago
Featured Stories
LIVE: What happens to unprotected eyes during a solar eclipse?
LATEST ENTRY
New York Yankees push back start time of April 8 game because of solar eclipse
What is a horseshoe cloud?
Egg prices rising again, an outbreak of bird flu could make it worse
It’s not just you. Here’s why pollen allergies are worse than ever
Oregon truck crash releases 77,000 salmon into wrong body of water
22 hours ago
Weather Near Lobnya:
- Balashikha , Moscow
- Moscow , Moscow
- Zelenograd , Moscow
We have updated our Privacy Policy and Cookie Policy .
Get AccuWeather alerts as they happen with our browser notifications.
Notifications Enabled
Thanks! We’ll keep you informed.
Driving directions
The route deemed to be the safest and simplest with minimal scope for error along the way. The default recommended route from Michelin.
The route offering the shortest distance to a destination via the most accessible roads. Journey times for this option will tend to be longer.
The most fuel-efficient route that also avoids toll roads.
My cost options
- B7 (Diesel)
- E5 (Unleaded)
- E85 (superethanol)
- CNG (Biomethane)
- H2 (Hydrogen)
My route options
- E5 (Unleaded) €1.700
- Route : Fast
- Distance in : Kilometres
- No restrictions
Services at Lobnya
- Route from this place
- Directions to this place
- Route via this place
- Nearby hotels
- Nearby restaurants
Alternative travel
Arrive at lobnya organise your trip, accommodation, other services, restaurants at lobnya.
- See restaurants from the Michelin selection
Tourist Attractions at Lobnya
- View the must-see tourist sites
Renting a car, an attractive proposition for the holidays
Monthly Report
Eco-mobility
Keep in contact
My michelin account.
Work in progress.
IMAGES
VIDEO
COMMENTS
Dodge Journey High Beam Lights On. This means your front high-beam driving lights are on. These lights are used for 0.01% of driving and typically for country roads late at night. Fines can apply for use of high beams in dense residential areas. Do NOT use high team driving lights within 400 metres (1,000 feet) of an oncoming car.
Dodge Journey warning lights & dashboard symbols explained for the years 2008 through to 2020. Find out what the dashboard symbols mean for your make, model and year of car. ... The Dodge Journey is a crossover SUV, and can be seen in left-hand drive countries, and well as right-hand drive countries, as the Fiat Freemont. Manufactured since ...
Name: Dodge Journey airbag warning light. Description: Under normal circumstances, the red airbag warning light illuminates on the dashboard for between 4 to 8 seconds when the ignition is switched to on/tun. This is a bulb check. If the airbag light no longer comes on, the bulb may be faulty and require replacement.
Dodge Journey Brake Warning Light. This dashboard light gets active when the parking brake is applied or there is a fault in an anti-lock brake system, may be the brake fluid level is getting low in your vehicle. Suppose this light stays on for a longer time than it indicates that parking brakes are disengaged. So, release the parking brakes as ...
Low fuel indicator -- click for more. Low washer fluid indicator -- click for more. Trouble or fault indicators. Electronic throttle control indicator -- click for more. Check engine light -- click for more. Electric power steering fault indicator -- click for more. Loose gas cap indicator -- click for more.
This indicator is typically only used for performance Dodge models that expect the driver to push them hard. The cause behind this could be heavy acceleration or in worst cases a loss of oil. As it is a red light you must pull over and allow the engine to cool down. If it persists then seek help from a mechanic.
The Dodge Journey comes with warning indicators just like other Dodge models. When these warning lights come up; it could be a system malfunction, security issue, or need for urgent maintenance. Driver safety shouldn't be taken for granted, especially when a warning light comes on. Taking a related risk could be bad for you and/or the vehicle.
To maintain the performance and safety of your Dodge RAM vehicle, pay attention to any warning lights that may appear on your dashboard. Remember, when the red or yellow symbols light up, take your car to a mechanic, or buy a scan tool to self-check. Don't miss my review on Best Chrysler/Jeep/RAM Scan Tools to find the right tool for you.
Learn the warning light's meaning and know possible solutions to fix the problem by checking the list below. This guide will explain Chrysler Dashboard Warning Lights and Symbols. Anti-lock brake System Fault Indicator. The system detects a fault if the ABS light remains on with the engine running. The ABS needs to be serviced.
1. Fix and Wait. The best way to clear the check engine light is to pull the trouble code, identify and fix the issue and then drive your Journey around until the module that threw the code recognizes that the problem is fixed. Sometimes it can take a few drive cycles for your vehicle's check engine light to shut down.
The most common causes for flickering dashboard lights and no engine crank in Dodge Journey are weak battery, corrosion on battery terminals, and bad ground connection. 1. Weak battery. The leading cause of flickering dashboard lights and no start in Dodge Journey is weak battery. You may also hear rapid clicking noise when you try to start the ...
I have a Dodge Journey Crew 2013 I have the ! & P lights (see attached image) that come on periodically, stay on for 30 or so seconds then clear. I took it into the Chrysler dealership and they didn't know what was wrong so had the tech check out the E-Brake and said thank you for $160 .. and the lights came on again on the way home.
Buy MZORANGE Tail Light Lamp Stop Brake Indicator Warning Light For Dodge Journey 2011 2012 2013 2014 2015 2016 2017 2018 with Bulb (Right Passenger Side): Tail Light ...
Region:U.S. Great Lakes. Journey's Year:2014. Posted April 18, 2016. Unplug the sensor, and make sure you did not bend a pin. They are touchy. Then disconnect the negative terminal of your battery for about 30 minutes to reset your system. See what happens. 2late4u, sidney john and OhareFred.
Buy MZORANGE LED Inner Tail Light Lamp Stop Brake Indicator Warning Light For Dodge Journey 2012 2013 2014 2015 2016 2017 2018 with Bulb (Right Passenger Side): Tail ...
What is the Dodge Electronic Throttle Control Warning Light? The Dodge Electronic Throttle Control Warning Light may indicate a problem with the electronic throttle control system. Some common causes of the light turning on include a bad throttle cable, broken or defective electric motor, and dirty air filters. In order to determine if the ...
The most likely cause of the warning light is a loose or damaged gas cap. To fix a loose gas cap, tighten it until it clicks. If the gas cap is damaged, you must replace it with a new one. Once you've fixed the problem, the Dodge gas cap warning light should turn off. If it doesn't, another issue with your vehicle may need to be addressed.
2012 Dodge Journey. Asked by Visitor in Marysville, MI on April 08, 2019. My battery has a parasitic drain and I believe it is caused because the dash board lights seem to stay on randomly even when all switches are off (i.e. ignition and dimmer setting) and doors are locked. When functioning properly, they shut off within 15 sec.
On Wednesday at around 5 p.m. local time, the lights suddenly went out in several areas of Omsk, including in both central regions of the city, and in rural areas, local media reported.
Lobnya Weather Forecasts. Weather Underground provides local & long-range weather forecasts, weatherreports, maps & tropical weather conditions for the Lobnya area.
Current Weather. 9:20 AM. 64° F. RealFeel® 72°. RealFeel Shade™ 65°. Air Quality Fair. Wind N 1 mph. Wind Gusts 1 mph. Sunny More Details.
ViaMichelin will help you to determine the best route based on various options and, by default, offer two to three routes with varying costs, distances and journey times. Some routes (e.g. the cheapest) may suggest quieter roads or avoiding tolls whilst others will offer a compromise between distance, travel time and cost for your journey ...