trip breaker box

• svg]:stroke-primary"> 826K
• svg]:stroke-primary"> 622K
• svg]:stroke-primary"> 246K
• svg]:stroke-primary"> 45K

Why Is My Circuit Breaker Tripping? 4 Potential Problems and Solutions

By: Glenda Taylor , Bob Vila , Evelyn Auer

Updated on Dec 21, 2023 8:55 PM EST

6 minute read

Photo: istockphoto.com

We may earn revenue from the products available on this page and participate in affiliate programs. Learn More ›

Q: Every few hours—sometimes minutes!—my living room and one side of my kitchen lose electrical power. I’ll check the breaker panel and, sure enough, a circuit breaker has tripped…again. Should I call an electrician, or is there a simple DIY fix I can try first?

A: While it’s frustrating when a circuit breaker keeps tripping, they are important safety mechanisms. Designed to shut off the electrical current when something goes wrong, circuit breakers are one of the best ways of protecting a home from an electrical fire. “When a circuit breaker trips, typically it is because we use too much electricity, which causes it to overload and turn off,” says Christopher Haas, expert electrician and owner of Haas & Sons Electric in Millersville, Maryland. For those who need an electrical panels 101 refresher course or aren’t sure how to reset circuit breakers, each breaker has an on/off switch and controls a separate electrical circuit in the home. When a breaker trips, its switch automatically flips “off,” and it must be manually turned back on to restore electricity to the circuit. For those wondering, “Is it dangerous if a circuit breaker keeps tripping?” the answer is that it can be, depending on the source of the problem. An electrician can ultimately deal with the root issue, but a little sleuthing will reveal whether it’s something that’s easily remedied.

In many cases, the cause of a circuit breaking tripping is an overloaded circuit.

A circuit overloads when more electrical current is being drawn through the wires than they can handle, tripping the circuit breaker. If this happens, there may be a few additional signs:

• Buzzing noises coming from outlets
• Devices charging slowly
• Electrical outlets not working
• Flickering lights
• Scorch marks on outlets and light switches

If a circuit breaker keeps tripping in one room, homeowners can test for circuit overload by turning off all the switches in the affected area and unplugging all appliances and devices. After the breaker is flipped back on, the devices can be turned back on one at a time, with homeowners waiting a few minutes in between to see if the circuit remains on. If the breaker trips before all the appliances are turned on, the experiment can be repeated, this time turning them on in a different order. It may be necessary to do this several times to find out how many appliances can be operated at once before the circuit overloads.

“As a short-term solution, you can unplug unnecessary appliances to prevent tripping circuit breakers. You may still get some trips, but you can limit them by unplugging devices that you don’t need to use,” advises Dan Mock, vice president of operations at Mister Sparky , an electrical company with 90 locations in the U.S. The best long-term solution, however, is to pay an electrician for the cost to rewire the house and add additional circuits. The cost to replace an electrical panel is about $1,274 on average.

Other times, the issue may be caused by a short circuit.

A “short” circuit means that two wires that should not be coming into contact are inadvertently touching, triggering a sudden surge of electricity through the wires. A short can occur in an outlet, a switch, or within an appliance if wires are loose or have been chewed through by mice or pets. Some signs of a short circuit include:

• Popping sounds
• Discolored outlets or switches
• Burning smells

Testing to see if an appliance has a short is similar to testing for an overloaded circuit. When an appliance that has a short in its wiring is turned on, it will immediately trip the circuit. Homeowners can also try plugging it into an outlet in a different room. If the breaker for that room trips, there’s a short in the appliance (if it’s unclear what breaker goes to what room, the breaker can be identified with one of the best circuit breaker finders ). Electrical shorts can be a major fire hazard, so it’s a good idea to call a licensed electrician for this circuit breaker repair. It’s wise to stop using the outlet or appliance until a pro takes care of the problem.

Another potential cause of a circuit breaker tripping is a ground fault.

A ground fault occurs when the electricity running through a home’s wiring diverts from the wiring loop and travels to the ground, usually due to faulty wiring or water infiltration in an outlet or switch box. Water is a conductor, which is why walking through puddles is often listed as something not to do in a power outage in case of downed power lines. Once water makes contact with wires, electricity can jump from the wiring loop and follow the water trail. This creates a surge in electricity leading to a tripped circuit breaker. If a person comes in contact with the electricity that is on its way to the ground, this can result in electrocution. Homeowners may notice a few signs of a ground fault, including:

• Tripped GFCI (ground fault circuit interrupter) outlets;
• A burning smell coming from an outlet; and
• Lights flickering.

Newer electrical breakers have features designed to protect against the danger of ground faults. According to Haas, “Ground fault breakers sense electricity going to earth as opposed to going through the wires of the circuit. You’ll find [these] for bathrooms, kitchens, garages, exteriors, and basements.” GFCI outlets are another safety feature that shut off the electric current within a fraction of a second of sensing a ground fault.

If a ground fault is the problem, the cause of the errant water must be discovered and repaired, and any damaged wiring must also be replaced. It’s also a good idea to install GFCI outlets in rooms where water is commonly used. A GFCI outlet costs $210 on average.

Sometimes a bad or worn-out circuit breaker can be the culprit.

In some cases, the circuit breaker itself may be faulty. Breakers that are old, damaged, or were installed incorrectly may trip frequently for no apparent reason. Alternatively, faulty breakers may not trip when they are supposed to, leaving the home at risk of electrical fire. Some signs of a bad circuit breaker include:

• The circuit breaker getting hot and tripping frequently;
• The circuit breaker won’t reset;
• It has been over 10 years since the breaker was last serviced; and
• The breaker has scorch marks.

An important electrical safety tip to keep in mind is that resetting a breaker over and over again can cause what is called an arc flash, which is a small electrical explosion that can be deadly. If resetting the breaker once does not remedy the issue, it’s a good idea for the homeowner to hire an electrician near them who knows how to replace a circuit breaker safely. Mock warns, “Don’t take any chances with circuit breakers. Instead, call a licensed electrician who knows the safe ways to replace breaker boxes, upgrade circuits, and diagnose potential electrical problems in your home.” Wiring a breaker box is a job to leave to an experienced electrician.

A professional electrician can help determine the specific cause of a frequently tripping circuit breaker.

Most circuit breaker problems—aside from those explained in the sections above—will need to be inspected and addressed by a licensed electrician. According to the Electrical Safety Foundation International (ESFI) , each year “thousands of people in the United States are critically injured and electrocuted as a result of electrical fires, accidents, [or] electrocution in their own homes.” While homeowners may be tempted to save on electrician costs by attempting circuit breaker replacement or repair themselves, electrical work is not suitable for casual DIYers. “Yes, you have to pay, but you can save many hours of head-scratching by hiring an electrician. Electricians will also have all the right tools for diagnosing and repairing the circuit,” Haas adds. “Lastly, they will come with a warranty/guarantee should something arise, and they will typically return at no additional cost.”

Anker’s New Home Battery Tower Is a Sleek, Modular Step Toward Complete Energy Independence Anker’s New Home Battery Tower Is a Sleek, Modular Step Toward Complete Energy Independence

By: Chase Brush

The 20 Best Lawn Care Products for a Lush and Healthy Lawn The 20 Best Lawn Care Products for a Lush and Healthy Lawn

By: Deirdre Mundorf

Circuit Breaker Tripping: Troubleshooting Guide

Hubert Miles | Licensed Home Inspector, CMI, CPI

Updated on January 5, 2024

A circuit breaker tripping results from short circuits, overloaded circuits, and ground faults. In each case, an unintended excessive flow of current triggers the trip. You must reset the circuit breaker by flipping it back on to restore power.

Circuit breakers trip because they cannot handle the amount of current running through them. Tripping the circuit breaker interrupts the flow of electricity and protects your devices or appliances from damage.

Get FREE estimates from licensed electricians in your area today. Whether you need to replace an outlet, hang a ceiling fan, a new electrical panel, or repair wiring, We Can Help!

Without electrical circuit breakers , the possibility of electrical fires would be much higher.  

This guide looks at what causes circuit breakers to trip, what you can do, and how to identify a bad breaker.

What Would Cause a Circuit Breaker to Trip

There are three leading causes of circuit breaker trips:

• circuit overload
• electrical faults (i.e., ground faults and arc faults)
• short circuits

Below are factors that can cause circuit breaker trips. 

Circuit Overload

A circuit overload happens when the flow of electric current running through the circuit exceeds the amperage of the devices it serves. 

For example, if your microwave is a 12.5 amp appliance, you can run it on a 15 amp circuit. That means your microwave is safe as long as the amperage running through the circuit is 15 amps .

However, if the circuit receives an excessive electrical load over 15 amps , it will automatically trip to protect your device from damage. If the circuit doesn’t trip, the excess current will fry the circuit in your microwave. 

Also, if you operate too many appliances and devices on one circuit, its internal mechanism heats up, causing the breaker to trip. 

Circuit overload is the most common reason for breakers tripping. 

Ground Faults

A ground fault occurs when the active wire comes into contact with a ground wire made of bare copper. Sometimes, this fault may happen when the hot wire touches the metal box connected to the ground wire.

Excessive current flows once the active wire touches the ground wire, flowing into the earth. If you step on the affected area, ground faults can cause shock and even electrocution. The uncontrolled flow of electricity will cause the circuit breaker to trip.

Arc Faults 

An arc fault happens when exposed faulty wiring touches, causing the electric current to arc at the meeting point. As a result, sparks occur, which can ignite an electric fire.

A corroded or loose connection is the main culprit for arc faults. Circuit overloads, ground faults, or short circuits trip an AFCI (Arc Fault Circuit Interrupter) circuit breaker.

Arc faults result from damaged, loose, or corroded terminals and wires. The arc fault builds up over time as the heat due to the cable damage and terminals build up to the point of ignition.

Short Circuits

A short circuit occurs when an active wire touches a neutral wire, and the electrical current takes an unintended path of least resistance. 

The common cause of short circuits is frayed wires coming into contact when the wires touch. The electrical current flow increases significantly, causing the circuit breaker to trip to stop the electricity from damaging appliances.

It is a short circuit because the current bypasses the proper circuit wiring channels and flows through a shorter, unplanned pathway.

Short circuits occur 

• When insulation melts and wires are exposed
• Within appliances with damaged internal wiring
• Due to damaged and frayed extension or appliance cords

How do You Fix a Breaker that Keeps Tripping?

A dedicated circuit breaker tripping indicates too much current flowing through the wiring or connection to the outlet.

Here is a step-by-step guide to follow when you notice the first trip:

• Begin by turning off all the appliances and unplug electrical devices from the outlet. Also, switch off light fixtures and unplug those that you can. This prevents any appliances from damaged when the breaker is reset and a sudden surge of power comes through.
• Open the circuit panel or box and locate the on and off buttons of the circuit breaker. You may notice an orange or red color on the breaker when it is off. 
• Flip the switch from off to on to reset the circuit breaker. Once the breaker is reset, you can switch and test the appliances to see if the electrical power is flowing.
• Keep safe as you reset the breaker by working from the side of the electrical box instead of the front. That way, you will avoid any sparks (should there be any) when you switch the breaker back on.
• Some people prefer to switch the main electrical switch when working on the circuit breaker for added safety. 

Types of Circuit Breakers

Standard circuit breaker.

Standard circuit breakers monitor the modulation of the electric current coming into your devices and appliances. 

This circuit breaker stops the current from flowing when it detects the excessive flow of electricity. 

Standard circuit breakers come in two forms:

• Single-pole circuit breakers
• Double pole circuit breakers

Single-Pole Circuit Breakers

Single-pole circuit breakers are the most common breakers in homes and buildings. They monitor the electric current’s flow in one wire and trip if that wire experiences a very high influx of electricity.

These breakers deliver only 120 volts and work well for 15 to 30 amp circuits. Single-pole circuit breakers come with one switch in the back. 

Double-Pole Circuit Breakers

The double-pole circuit breakers monitor the current in two wires simultaneously. You will notice two switches on the back of these breakers.

The double-pole circuit breakers will trip even if only one of the wires receives too much current. They can accommodate between 15 to 200 amps while delivering 240 volts. 

Single-pole breakers are a good fit for lighting fixtures and other standard home outlets. On the other hand, double-pole breakers work for larger appliances like dryers and washing machines. 

Ground Fault Circuit Interrupter (GFCI)

The GFCI circuit breaker interrupts the line due to ground faults. They trip when the current starts to follow an uncharted path into the ground. These ground fault surges occur when a foreign conductor, like water, comes in contact with a receptacle .

At the same time, they offer protection against circuit overloads and short circuits. 

GFCI circuit breakers come built into specialized outlets required for wet areas in the home, including :

• Outdoor areas like the balcony, patio, porches, and decks
• Laundry rooms
• Swimming pools
• Six feet from a sink
• Six feet from the bathroom

These breakers help prevent shock or electrocution should the electrical outlet contact water. 

Arc Fault Circuit Interrupter (AFCI) 

The AFCI circuit breaker detects normal and abnormal arc faults, so it will trip when it detects a dangerous arc fault that can cause a fire. 

The AFCI circuit breaker doesn’t work to protect devices and appliances plugged into an outlet. It works to prevent electrical fires due to faulty connections and wiring. The internal sensing mechanism in the circuit breaker senses the conditions of an electric arc, and the circuit trips to avoid an electric fire.

AFCI protection can also be built into an outlet. The National Electrical Code (NEC) requires these types of breakers to feature in :

• Common rooms
• Laundry areas

AFCI and GFCI circuit breakers can co-exist and complement each other for the best protection.

Combination All Fault Circuit Interrupter (CAFCI)

The CAFCI breaker senses and reacts to any electrical fault, including ground and arc faults.

CAFCI is a relatively new technology that meets new NEC requirements for circuits requiring arc and ground fault protection.

Do Circuit Breakers Get Weak?

A circuit breaker can wear out and become weak. If a breaker trips frequently, the thermal or magnetic element can lose calibration, causing it to trip at lower amp loads than intended. A breaker constantly under thermal stress caused by overloading the circuit will eventually trip more frequently.

Let’s not forget breakers are not impervious to damage. As the internal mechanical parts wear out, they become very sensitive and may not hold under normal load amperage and temperatures.

Electricians refer to this as a bad breaker .

Will a Bad Breaker Keep Tripping

By definition, bad breaker malfunctions, so it will keep tripping until it is either replaced or rectified .

A licensed electrician performs this simple test to see if a breaker will keep tripping and determine if it can be repaired or replaced in the following steps.

• The electrician will switch off all the fixtures and appliances in the house. Also, unplug everything.
• Find the malfunctioning circuit breaker . The electrician will go to the electrical box and locate the breaker lighting orange or red or the one with the switch off.
• They will ascertain that it is the correct circuit breaker. After that, the electrician puts the breaker off.
• With the switch on, the breaker is back on as well. The electrician will plug the appliances into the outlet with the problem circuit breaker. Now, they will turn the devices and appliances on. 

If the breaker trips, the electrician will investigate the circuit’s current amount. The breaker is bad if the current is according to the appliance’s rating.

How You know if a Circuit Breaker is Bad

Breakers do wear out after a while. It has a problem if the breaker doesn’t stay on after resetting it.

Since the circuit breaker controls the electric flow in the house, it is essential to monitor it and catch signs that it has gone bad early.

Here are key signs that denote a bad circuit breaker :

It Frequently Trips

Frequent tripping could be because of a bad breaker. After tripping and resetting, your circuit breaker should stay on unless it detects high current flow. 

To ensure that the issue is not the electricity but the circuit breaker, call an electrician to examine your electricity’s flow and determine whether it is the cause of the constant tripping.

If it is not, then the circuit breaker is the problem. 

The Breaker Overheats

Electrical systems will heat up when active. Typically a breaker can heat to about 60°C (140°F) before problems arise.

Terminations for standard rated breakers: UL 489 Paragraph 7.1.4.2.2 says the temperature rise on a wiring terminal at a point to which the insulation of a wire is brought up as in actual service shall not exceed 50°C (122°F). Terminations for 100% rated breakers: UL489 Paragraph 7.1.4.3.3 says the temperature rise on the termination shall not exceed 60°C (140°F). Handles, knobs, and other user surfaces: UL489 Paragraph 7.1.4.1.6 says the maximum temperature on handles, knobs, and other surfaces subject to user contact during normal operation shall not exceed 60°C (140°F) on metallic and 85°C (185°F) on nonmetallic surfaces. Source: https://www.clipsal.com/faq/fa173839

Call an electrician immediately if the breaker becomes too hot.

There are Scorch Marks

Scorch marks around receptacles, appliances, and the electrical box should tell you your circuit breaker has gone bad.

The burn marks indicate that wiring insulation has melted off and the circuit wires are now sparking and emanating heat or fire. That means that the circuit breaker did not interrupt the excess current and reached the wires and burned them. 

You may see melted wire sheathing on the wire where it connects to the breaker.

Professional electricians can use a  thermal imaging infrared camera to locate the heat source. The infrared camera allows them to pinpoint the problem area through the walls and other construction material.

A Burning Smell

Sometimes you may smell the insulation burning, but no scorch marks are present to denote which outlet is the problem. 

With the help of the infrared camera, an electrician can help locate electrical issues. 

If you encounter a burning odor, shut off the main power and call for emergency service from an electrician. 

The electrical wires burn because power surges through the circuit, melting the wire insulation.

What is Nuisance Tripping

Nuisance tripping is when a breaker trips without a fault to warrant the interruption to the electric current flow.

Nuisance tripping occurs due to several reasons:

Stringent Protection on Circuits 

Sometimes the circuit is protected by stringent conditions that detect any variance as a fault and cause a trip. 

Such stringent conditions can be tuned to accommodate the home’s or building’s electric needs.

A Highly Sensitive Circuit Breaker

In some cases, the circuit breaker has been set to susceptible settings so that they can detect even the slightest fault, even a minor average variance.

For example, the manufacturer can set an AFCI circuit breaker to sensitive standards to detect another circuit’s arc. This common issue may occur in a daisy chain where the circuit breakers connect in a linear series. There may be a faulty electrical outlet you are unaware of on the circuit. It is common for multiple rooms to share a breaker in older houses.

The Breaker Encounters Power Under Different Conditions

The variation in the current is normal, but the breaker responds to it by tripping because the flow is outside the breaker’s regular operation.

Your circuit breaker is tripping because the voltage it is encountering is not within the standard operation. You will need to adjust the circuit breaker or the voltage to eliminate nuisance tripping.

The Breaker Trips with Nothing Plugged in

A breaker tripping with nothing plugged in occurs when a hot, neutral wire is touching somewhere in the circuit. The common causes include frayed or damaged electrical wires, loose connections, faulty electrical receptacles, light switches , or dimmers.

Electrical wire damage happens when:

• wiring is chewed by animals such as rats, squirrels , raccoons, etc
• wire sheathing and insulation ages and become frayed
• wires rub against sharp edges such as punch-outs with missing grommets or wire clamps

Loose connections often occur when electrical wire nuts come loose or electrical tape wears out causing wires to touch.

Defective wiring can be anywhere along the circuit, so it’s best to contact a licensed electrician to troubleshoot why the breaker is tripping.

Replacing a Bad Circuit Breaker

• Check the electrical panel to see the compatible approved circuit breaker brands. Also, make a note of the brand of the electric panel . This is to help you determine if there are upgrades they could recommend for the hardware.
• Order online or go to the hardware store and purchase the breaker of the same voltage as the one you are replacing.
• Go and open the electrical box and switch off the bad breaker. Loosen the terminals and remove the wires using a pair of needle-nosed pliers. Ensure the pliers have rubber insulated handles to avoid shock or electrocution since you will use the pliers to grab the live wires from the terminal. That is a safety measure.
• Remove the bad breaker. Replace it with the new breaker and slip its clips into place. Remember to switch off the replacement breaker.
• Next, using the pliers, hold the wiring and tighten the screws on the terminal. It is crucial to ensure that the wires and screws in the terminals are in the right place.
• Turn the breaker on and replace the electrical panel cover.

Can a Breaker Fail Without Tipping

If you have a newer electrical panel , it’s not likely for a breaker to fail and not trip. However, in older breaker boxes like Federal Pacific , the breaker failing to trip is common.

The main reason Federal Pacific was investigated by the Consumer Products Safety Commission (CPSC) was widespread structure fires involving breakers failing to trip when an electrical overload was present. They found that the circuit breaker contacts would fuse to the bus bar.

Modern breakers will trip when a failure occurs as an added layer of safety. Most older breakers did not have these safeguards.

With AFCI breakers, if the Internal sensing mechanism fails, the breaker reverts to a standard breaker. The AFCI sensor mechanism will no longer work, but the breaker would still trip from overcurrent protection. Therefore, you should test the AFCI breaker regularly.

Conclusion 

Listen to your circuit breaker . It’s alerting you of a problem when it trips. That communication could be a problem with the breaker itself, the circuit, or the amount of electric current coming into your home.

Hubert Miles is a licensed home inspector (RBI# 2556) with more than two decades of experience in inspection and construction. Since 2008, he has been serving South Carolina through his company, Patriot Home Inspections LLC. As a Certified Master Inspector, Hubert is dedicated to providing his expertise in home inspections, repairs, maintenance, and DIY projects.

Continue Reading

Watts to Amps Calculator: DC/AC Wattage to Amps Conversion

70 Amp Wire Size: Breaker & Wiring Gauge Guide

80 Amp Wire Size: Breaker & Wiring Gauge Guide

200 Amp Wire Size: Service Length & Wiring Gauge Guide

10/2 or 10/3 Wire for Mini Split: A Professional Guide

GFI vs GFCI: Understanding the Key Differences

Founded by Hubert Miles, Certified Master Inspector

Home Inspectors

Calculators

Privacy Policy

Terms of Service

©2024 Home Inspection Insider 898 Whispering Pines Rd, Johnsonville, SC 29555 843-250-1882

How to Reset a Tripped Breaker

What to do when a circuit breaker trips.

Lee has over two decades of hands-on experience remodeling, fixing, and improving homes, and has been providing home improvement advice for over 13 years.

The Spruce / Kevin Norris

What Causes a Tripped Circuit Breaker

Safety considerations, how to avoid tripped breakers, when to call a professional.

• Total Time: 5 mins
• Skill Level: Beginner
• Estimated Cost: $0

A power breaker trip is an annoying occurrence when the power shuts off and you can't use the microwave, lights, or router. A breaker trip is far more than simply annoying when you need that router to send off a time-sensitive work assignment or when medical devices are diverted to time-limited standby power. Fortunately, it's easy to fix a circuit breaker trip in just a few minutes.

Tripped Circuit Breaker

A tripped circuit breaker is when a circuit breaker automatically shuts off to prevent devices on the circuit from overheating or from receiving excessive power. A circuit breaker protects your home against damaging or harmful short circuits and overloads.

• Overloaded circuits : When too many devices are operating on the same circuit and are attempting to pull a higher power load than the circuit can carry, the circuit breaker will trip.
• High-power devices : High amp devices like microwaves , dryers , wall heaters , or A/Cs are turned on for sustained periods, they can cause a power breaker trip.
• Short circuits : In a short circuit, a powered or hot wire makes contact with a neutral wire or when wires are loosened .
• Ground faults: In a ground fault, a hot wire touches anything that is grounded, such as the side of a metal electrical box , an appliance, an outlet , or a bare ground wire.

Need more help? Talk to an electrician near you

Our partners can help you compare quotes from top-rated professionals near you

Get a Quote

Watch Now: How to Safely Reset a Tripped Circuit Breaker

Working around an electrical service panel or circuit breaker board can be dangerous. Your home’s entire electrical load is contained in that box, concentrated around the metal lugs where the service drop’s wires enter the box. Unscrewing and removing the inner dead-front cover within the service panel exposes the highly powered lugs.

What You'll Need

Equipment / tools.

• Circuit breaker directory (if available)
• Rubber-soled shoes
• Safety glasses

Instructions

Locate a flashlight.

Circuit breaker panels tend to be located in out-of-the-way locations with little, if any, ambient light. Find a flashlight. Use the light from a phone if necessary.

Turn Off Devices on the Circuit

Turn off all devices on the electrical circuit. This includes the device that may have caused the breaker to trip, such as a microwave, hairdryer, or A/C, plus all other devices on the same circuit.

Find the Electric Service Panel

The electric service panel, sometimes called a circuit breaker board, is a metal box with a door. The box may be inset in a wall, its face flush with the wall, or surface-mounted where the entire box is exposed.

Places to look: garage , closet, pantry near the kitchen, basement , mudroom, hallway leading to garage or backyard.

One clue is to first find the electric service drop from the main power lines. Usually, your home’s service panel is located below and nearby, on the inside of your home.

Open the Door to the Service Panel

Open the door to the service panel by sliding the plastic switch to the side or up. Next, swing the door open. Use the inset plastic switch as a handle to pull the door open.

Adhi Syailendra / Getty Images

Locate Tripped Breaker

The handle of a tripped circuit breaker should be in the middle position—not left or right. Visually or by feel, locate any breaker handles that differ from the right or left positions:

• Tripped breakers : Tripped circuit breakers have a soft or springy feeling when you lightly press them leftward or rightward.
• Live/active breakers : Breakers that are not tripped are either firmly left or right (depending on which side of the box you're looking at).

Certain breakers, such as Eaton breakers , trip to the off position, not the middle position. Check manufacturer's instructions for your particular product.

Turn the Circuit Breaker Handle to OFF Position

Flip the circuit breaker handle to its firm OFF position, toward the outer edge of the service panel (away from the centerline).

Double and Tandem Breakers

Double pole breakers are double-wide breakers with wide handles. They are often used for dryer or oven circuits. Both sides of double pole breakers operate as one. Tandem breakers are two narrow breakers that share the space of one breaker. Each side operates individually.

Turn the Circuit Breaker Handle to ON Position

Flip the circuit breaker handle to its firm ON position, toward the centerline of the service panel. The handle should seat firmly in place and should make an audible click.

Test Circuit

Turn the device such as the light or A/C back on. If you believe the breaker tripped due to an overload, it’s best to turn on only one device at this time, not multiple devices. Also, choose a device with a lower power draw such as a light fixture.

• Remove some devices from the overloaded circuit and plug them into other circuits that aren’t drawing as much power.
• Avoid running many devices on the circuit at the same time. In a kitchen , for example, stage cooking activities that require power so that they happen in succession, not all at once.
• Install GFCI outlets so that the outlet shuts off before the entire circuit breaker shuts down in the case of a ground circuit. Just note that GFCI outlets are not circuit overload protection, but protection against dangerous ground faults.
• Replace old outlets, light fixtures, and switches which may create short circuits or trip breakers.
• Have an electrician separate hardwired devices that are drawing too much power from a single circuit. The electrician can move devices to another circuit or can set up an entirely new circuit to relieve the load.
• Replace the circuit breaker.

A qualified, licensed electrician is trained to detect the cause of tripped breakers and to fix those causes. If your problem of tripped circuit breakers is more than just an overloaded circuit, you may want to seek the help of an electrician. Unless you are an advanced do-it-yourselfer , it’s best to hire an electrician to wire up a new circuit breaker .

Electrical Panel Safety . Office of Congressional Workplace Rights.

CH Circuit Breakers . Eaton.

Ground-Fault Circuit Interruptors . International Association of Certified Home Inspectors.

More from The Spruce

• GFCI Receptacle vs. GFCI Circuit Breaker
• Ground Fault vs Short Circuit: What's the Difference?
• Calculating Electrical Load Capacity for a Home
• What Is a Circuit Breaker Panel?
• What Happens When a Fuse Blows
• Understanding Arc Faults and AFCI Protection
• Line vs. Load Wiring: What's the Difference?
• Understanding Fuses and Fuse Boxes
• Subpanels Explained for Home Owners
• A Basic Guide to Home Electrical Wiring
• How to Reset a Circuit Breaker
• Amps vs. Volts: The Dangers of Electrical Shock
• Basic Electrical Knowledge for Your Next Home Project
• How to Cap Electrical Wires
• What Is a Short Circuit, and What Causes One?
• Line or Load With GFCI Connection

• Account Settings

Home Services

• Home Security
• Pest Control
• Living Room
• Other Rooms

Home Improvement

• Cost Guides
• Floor Plans
• Housekeeping
• Cleaning Tips
• Organization
• Popular Brands
• Sizes & Dimensions

Smart Living

• Dangerous Areas
• Safest Areas
• Most Affordable Areas

Top stories

Breaker Tripping With Nothing Plugged In (Why & How to Fix)

When we think of a circuit breaker that keeps tripping, common wisdom would be that you’re dealing with a home that’s using up too much energy. So, if it’s happening to you, you might unplug some stuff. But, sometimes, the breaker just will keep tripping regardless of how much stuff you unplug. Clearly, it’s not energy consumption anymore. So, what gives?

A circuit breaker can trip when there is nothing plugged in if there is a ground fault or the circuit breaker is outdated. Damaged wires within the circuit breaker can cause it to keep tripping for no reason. The average circuit breaker lasts for 35 years, and they can trip with nothing plugged in when they are over 30 years old.

Circuit breakers are necessary to prevent electrical problems, expensive damage, and most importantly fires. It can be alarming when your circuit breaker keeps tripping when there is nothing plugged in. Follow along as we explore what it means when your circuit breaker trips for no apparent reason.

Do You Need to Hire an Electrician?

Get free, zero-commitment quotes from pro contractors near you.

Why Would A Circuit Breaker Trip Without Anything Plugged In?

A breaker is meant to break electrical currents due to an overload, so it really shouldn’t be breaking without anything plugged in. This means that you might be dealing with an electrical issue regarding the breaker. This can be potentially dangerous, so it’s important to troubleshoot this as soon as possible, and call an electrician to fix it.

Troubleshooting Your Circuit Breaker

So, you already know that you’ve got a breaker that’s not doing what it’s supposed to do. What should you do now? The answer, clearly, is that you are gonna have to troubleshoot your circuit breaker . Here’s how to do it:

• Before anything else, check to see that you don’t have anything that could be causing the breaker to trip.  If your breaker’s tripping is related to two rooms, check to see that it’s not your DJ equipment or extra-large entertainment set up in the next room that’s causing it.
•  Check the input wires for damage.  If you notice that they’re frayed or have reason to believe that their movement is causing the breaks, call an electrician. You need to get the input wires replaced or fixed.
• Reset the breaker. Remove all connected items in your room from their plugs and reset your breaker. If it breaks again, then there is an issue that you have to fix.
• Keep an eye out for signs of a short circuit, fuse issue, or ground fault. When you’re dealing with a short circuit, you might notice a burn mark or a smell near an outlet. With a ground fault break or fuse issue, you may have a problem with wiring overheating or being exposed to water. If you believe you have an issue with this, give an electrician a call.
• If all else fails, you have a faulty breaker.  Even circuit breakers will eventually need to be replaced. They will eventually go bad. If you can’t find anything else wrong, it’s time to get a new circuit breaker. If you’ve had your circuit breaker for a very long time, it’s possible that your breaker just ran its course and needs to be replaced.

However, there are several problems that range from a ground fault to an outdated circuit breaker that you need to consider. Let’s take a look a the most common reasons that your circuit breaker keeps tripping when nothing is plugged in.

Ground Fault

A ground fault, or earth fault, is when an active wire touches the earth . Ground faults occur when a wire and the ground interact and overload the circuit breaker with the current. There is no resistance or restrictions with the earth, so an unrestricted flow of current goes through the wire and to the circuit breaker.

A ground fault is similar to a short circuit because the current bypasses the circuit wiring . The reaction from a ground fault is immediate, and the circuit will immediately flow uncontrollably. Between the lack of resistance and increased current flow, a ground fault can trip your circuit breaker and potentially damage it permanently.

Electricians treat a ground fault differently than a short circuit, but both problems require a fix. Ground faults are dangerous to fix or come into contact with, and there is potential for electrical shock.

Outdated Circuit Breaker

Circuit breakers have a lifespan just like any other key electrical fixture in your home. The average circuit breaker lasts for 35 years , but they can last for up to 40 years. You can generally tell that your circuit breaker is outdated when it acts up, and old breakers often trip when nothing is plugged in.

Worn breakers are less conductive and reliable, and they are often difficult or impossible to reset . Old circuit breakers produce a distinct burning smell that can be alarming. The voltage and current strength on an outdated circuit breaker are unpredictable and fluctuate wildly.

If your circuit breaker is nearly 30 years old and often feels hot, it is likely outdated . Replace your old circuit breaker if it frequently trips with nothing plugged in after you reset it

Old homes have different wiring configurations than modern homes, and that can affect your circuit breaker. Generally, old homes have circuit breakers that work via a single circuit. A single circuit is not enough to keep up with the electrical demands of modern homes .

Homes that are 40-50 years old or older likely have single circuit units that affect multiple outlets and even rooms. Your circuit breaker can trip even if there is nothing plugged in if you have an old home with outdated wiring and an underpowered single circuit system. The only solution, in this case, is to replace your circuit breaker and update your wiring.

Short Circuit

Similar to a ground fault, a short circuit occurs when the electrical flow goes through a short path that it wasn’t supposed to . A short circuit can easily occur if the insulation on a wire is damaged and leaves them exposed. The most common cause for a short circuit is when multiple wires become exposed and touch each other.

The current essentially takes a shortcut instead of going through the circuit wiring. Short circuits cause a massive spike in current flow that overloads the circuit breaker and causes it to trip. It is good that your circuit breaker trips during a short circuit because that can prevent expensive and harmful damage.

Lamps, electric space heaters, and plug-in appliances commonly cause short circuits. Luckily, modern devices generally have well-insulated wires to prevent short circuits. However, a short circuit can happen when nothing is plugged in because the breaker’s wires themselves can cause a short.

Damaged Wires

The wires inside of and connected to a circuit breaker are well-protected, but they can still succumb to damage. Wires are covered with insulation that can melt over time and leave them vulnerable to damage. You should be concerned if you have a damaged input wire because that can be dangerous to touch or work with .

A damaged wire can cause a current leak and your circuit breaker will trip when it recognizes it. This is a safety precaution and prevents the current from going where it shouldn’t and causing a bigger problem. It is ideal to hire a professional electrician to repair damaged wires in your circuit breaker because it is complicated and potentially dangerous.

How Much Does It Cost To Replace a Circuit Breaker?

It costs an average of $1,250 to replace an entire circuit breaker box . However, you can expect to pay $1,800 or more for an upgraded circuit breaker box, but it may be worth the added safety. Replacing single switches on a circuit breaker is much cheaper and that generally costs $45 per switch .

You can spend as little as $205 to replace an AFCI circuit breaker in some cases, but it can cost $280 or more. It is worth the cost to replace a circuit breaker because it is difficult and dangerous to replace one without professional help. However, you need to refer to local building codes if you replace your circuit breaker as a DIY project to save money.

Can You Replace A Circuit Breaker On Your Own?

Technically, most people would agree that this could be a DIY job. However, I’m a little skeptical. With electricity, working on it without much knowledge of what you’re doing is a lot like trying to shoot an arrow up in the air and hope that it won’t hit anything. You might be fine, but you might not be.

If you choose to go the DIY way, just make sure that your local building codes allow you to do this. Many cities now require all electrical work to be done through the use of a certified electrician. So, if you aren’t sure, check with your local municipal office to find out whether DIY is an option.

Related Questions

How long do circuit breakers last.

Circuit breakers last for an average of 35 years , but they can last for up to 40 years. You can tell that you need to replace your circuit breaker if it won’t hold a reset or you notice a burning smell coming from it. Generally, circuit breakers become less conductive when they are old and trip more often.

Why does the circuit breaker trip when lightning strikes

A circuit breaker can trip when lightning strikes because it detects the thousands of amps that come from it . The current from a lightning strike is overwhelming and would overload your home’s electrical grid. It can trip even if the lighting doesn’t touch your house because a circuit breaker can detect the current in the earth or air.

Ossiana Tepfenhart is an expert writer, focusing on interior design and general home tips. Writing is her life, and it's what she does best. Her interests include art and real estate investments.

More by Ossiana Tepfenhart

What Items Cannot Be Moved By Professional Movers?

Popular articles.

20 Creative Ways A Shed Can Be Used For More Than Storage

10 Tips To Make Hand Washing Clothes Easier

10 Ways To Pick Flowers Without Damaging The Plant

Ways To Help Keep Your Dog Cool In The Yard This Summer

When Is It Worth It to Hire Professional Movers?

You may also be interested in.

Easily Install Crown Molding (On Cabinets That Go To The Ceiling)

How to Hang Double Curtains Without A Double Rod

How to Calculate Linear Feet For Kitchen Cabinets

Tamper-Resistant Outlet Can't Plug-In: Possible Solutions

Are Curbless Shower A Good Idea? (and Possible Problems)

6 Septic Tank Alternatives For Land That Won't Perk

How To Report A House That Should Be Condemned (It's Super Easy!)

Ceiling Fan Turns On By Itself? (Here's What You Can Do)

The 15 Most Dangerous Cities In Texas: 2022's Ultimate List

Onkyo Receiver Not Making Sound? (Possible Causes & Fixes)

12 Washing Machine Brands to Avoid [with Recall Data]

What Size Screws to Mount A Samsung TV? (It Depends!)

No Water Dispensing From Hot Side of Faucet? (Here's a Fix)

What Are the Parts of a Sink? (with Detailed Diagram)

10 Most Dangerous Neighborhoods in Baltimore [Updated]

Different Types of Ductwork (with Diagram)

Standard Home Bar Dimensions (with Drawings)

Why Does My Refrigerator Water Line Keep Freezing? (Fix It Now!)

WhatsApp Our Local Electrician To Get a Fast Response & Quote For Your Electrical Needs.

What Causes Circuit Breakers To Trip?

• May 2, 2024

Should your circuit breakers frequently trip, there’s no cause for alarm. It’s quite a common occurrence. Below are explanations for why this happens and advice on how to prevent it in the future. Master your circuit breaker problems!

Table of Contents

Understanding Circuit Breaker Tripping

Circuit breakers are protection devices for electrical circuits. When too much current passes, the breaker trips, stopping the flow of electricity and preventing damage. This can be caused by faulty wiring, too many appliances on one circuit, or a ground fault.

Overloading can cause tripping. This happens when too many devices are connected to a single circuit. Heat builds up in the wires, which can start fires or cause damage. To prevent this, distribute loads across multiple circuits and don’t connect too many appliances to one outlet.

Short circuits also lead to tripping. This happens when two wires with opposite charges come in contact or when a wire touches something grounded. This causes an immediate surge in current that triggers the breaker. Check for exposed wires or insulation damage, and call an electrician if you spot any signs of trouble.

Ground faults can also cause tripping. This happens when there’s an unintentional connection between a live wire and a conductive surface. Install GFCIs to avoid this.

In short, know what causes circuit breakers to trip. Identify potential hazards like overloading, short circuits, and ground faults. Take steps to prevent accidents and ensure your electrical equipment is safe. If you’re unsure how to handle electrical problems, call a licensed electrician.

Overloading Causes

Circuit breakers trip to stop overheating, electrical fires, and damage to electrical parts. Plugging in too many devices can cause the circuit to become overloaded, so the breaker trips to cut off the power.

Short circuits are like a blind date gone wrong. They can be explosive, and often end in disaster. This happens when a hot wire comes into contact with a neutral or insulation/water. This throws off the electric balance, causing danger and tripping.

Short Circuit Causes

A short circuit happens when a low-resistance path appears between two points in the circuit that aren’t usually connected. This can cause too much current to flow, making a circuit breaker trip. Insulation or wiring damage, faulty appliances, and circuit overload are the most common reasons for a short circuit. It’s critical to identify and fix the root cause quickly to avoid electrical fires and other dangers .

When too much power passes through a circuit, the circuit breaker will automatically turn off. It’s designed to protect wiring and guard against electrical accidents . But if the breaker trips regularly, there may be underlying issues that need investigation and repair. Often times, this means upgrading or replacing components.

Sometimes short circuits are caused by human error or wear and tear. But they may also come from design or installation problems. Planning and upkeep from local electricians can keep electrical systems running safely and appropriately for a long time. If your circuit breaker is tripping a lot, get an experienced technician to review your system and suggest solutions that match your needs and budget .

Overheating Causes

Circuit breakers are essential safety features. They stop electrical fires and protect your appliances. When overloaded, too much current flows, producing heat. This causes the breaker to trip!

Other factors can cause overheating. Damaged insulation on wires increases resistance. Loose connections add resistance and heat. High temperatures and poor ventilation worsen the situation.

It’s important to maintain and service the electrical system. Checks of all components will make sure they work efficiently. To avoid tripping, prevent overheating. This will reduce energy consumption and safeguard equipment. So, let’s learn about circuit breakers and how they deal with overloads!

Circuit Breaker Types

Circuit breakers are essential for any electrical system. They prevent overloaded and faulted circuits . There are different types of circuit breakers suitable for specific electrical loads.

See the table below for the different types of circuit breakers and their functions:

It is crucial to select the right type of breaker. Each one has its own advantages in specific situations. For instance, thermal circuit breakers are perfect for small appliances like hair dryers or irons . Meanwhile, magnetic circuit breakers are great for bigger loads such as air conditioners or refrigerators .

Remember, circuit breakers are like Beyoncé – they can handle a lot, but have their limits.

Circuit Breaker Ratings and Specifications

Circuit breakers are designed to protect electrical circuits from overloads. To ensure that circuits and appliances are safe, the ratings and specifications of circuit breakers need to be understood.

If a circuit breaker trips often, it may mean there’s an issue. It’s best to get professional help in these cases. Time to go on a hunt for your electrical wiring!

Troubleshooting Circuit Breaker Tripping

Circuit breakers can flip out for multiple reasons, like overloads , short circuits , and ground faults .

Overloads happen when too much electricity passes through the circuit, creating too much heat and tripping the breaker. Short circuits are when two or more wires touch, resulting in extra current. Ground faults occur when the power takes an unexpected route, like through a person’s body.

To figure out why your circuit breaker is tripping, it’s important to figure out what is going on and act accordingly. Inspections and maintenance can also help avoid future tripping.

Stop your circuit breaker from misbehaving with these prevention tips!

Preventing Circuit Breaker Tripping

A circuit breaker tripping can be prevented with understanding. When circuits are overloaded, breakers trip to avoid overheating and potential fires. Here are 3 steps that can help you prevent circuit breakers tripping:

• Know the electrical load – work out how many appliances & devices are connected to one circuit. Don’t overload them by spreading high-energy equipment across multiple circuits .
• Look after your appliances – ensure all your appliances & devices are in good condition, with no damaged cords or frayed wires.
• Upgrade your system – if you’re tripping breakers often you may need to upgrade the electrical system with higher capacity breakers or more circuits.

Plus, investing in surge protectors can also assist in preventing circuit overload and subsequent tripping of breakers. By following these steps you can make sure your home’s electricity runs safely and without interruption due to circuit breakers tripping.

Remember: these precautions will keep you from tripping more than just your circuit breakers!

Safety Precautions

Safety must be taken seriously when dealing with circuit breakers . Always switch off the main power supply before beginning work. Wear protective gear such as insulated gloves and boots to stay safe from electrocution. Never touch wires or components inside the box without proper training. Keep the area around the breaker box free from any flammable substances. Inspect breakers for damage or wear regularly .

Label each circuit breaker correctly . Test them frequently for functionality. This will help identify circuits quickly in case of an emergency. These precautions and practices ensure safety while dealing with circuit breakers. When in doubt, blame it on the circuit breaker – it’s always a good scapegoat for electrical woes!

Circuit breakers are essential components of any electrical system. They stop too much current flowing and thus, protect against potential fires . The most common cause for tripping is overload. But, other causes like short circuits and ground faults can also cause the breaker to trip. When it trips, there is something wrong that needs to be fixed right away.

Short circuits occur when two wires touch each other. This creates a low resistance path which allows a lot of current to flow with no load. Ground faults occur when the hot wire touches something incorrectly wired or with a damaged cord.

To prevent tripping, regular maintenance of the electrical system is needed. Keeping appliances in good condition, replacing worn-out cords and fixtures, and periodically checking for loose wires all help reduce the chances of tripping. In summary, understanding why the breaker trips and taking precautionary measures will keep you safe and save you repair costs.

Frequently Asked Questions

1. what causes a circuit breaker to trip.

There are several possible causes, including overheating due to circuit overload, short circuits, ground faults, and age-related wear and tear.

2. How can I prevent my circuit breaker from tripping?

You can avoid overloading your circuit by keeping the number of electrical appliances used on one circuit to a minimum, regularly checking wires for signs of wear and tear, and not using too many extension cords.

3. What should I do if my circuit breaker keeps tripping?

If your circuit breaker is constantly tripping, it is important to identify and fix the underlying issue. Contact an electrician to inspect and repair any faulty wiring or electrical devices.

4. Can a circuit breaker trip without an overload?

Yes, a circuit breaker can trip due to a short circuit or a ground fault, which may occur without an overload.

5. How do I reset a tripped circuit breaker?

To reset a tripped circuit breaker, turn it off and then back on again. Make sure to identify and correct the underlying issue that caused the trip before restoring power.

6. What is the lifespan of a circuit breaker?

The lifespan of a circuit breaker can vary depending on usage and other factors. However, most circuit breakers last between 10 and 30 years.

Related posts:

• What to Do in an Electrical Emergency
• How to Prevent Circuit Breaker from Tripping
• Tips for Hiring an Electrician for Commercial Properties
• Most Dangerous Home Electrical Hazards in Puchong

(912) 602-3068 | Need Power? Call Clocktower!

(912) 602-3068

How to Fix a Tripped Circuit Breaker That Won’t Reset

• March 26, 2024
• Electrical Tips

Have you ever had a circuit breaker trip and found that it won’t reset? It’s a common problem, and one that can be frustrating when you’re not sure what to do.

The most common reasons for a circuit breakers that won’t reset are:

• Damaged breakers
• Electrical shorts
• Loose wiring
• Damaged insulation

In this post, we’ll walk you through how to check for each of these common reasons, and discuss how to fix them.

Why circuit breakers trip

A circuit breaker is a safety device in your home designed to stop the flow of electricity if there’s an overload, which can help prevent fires. When the current flowing through the circuit breaker becomes too much for it to handle, it “trips” and shuts off the power to prevent a fire from starting.

Most of the time, resetting a tripped circuit breaker is a simple matter of flipping the switch back to the “on” position. However, sometimes the breaker won’t reset no matter how many times you flip it.

First, try to reset the tripped circuit breaker

First, we should perform a basic test to make sure the breaker is actually malfunctioning. If you haven’t already tried manually resetting the circuit breaker, this is the place to start.

Locate your circuit breaker box and open the cover. Once you’ve located the tripped breaker, flip it to the “Off” position. Then, flip it back to the “On” position. You should hear a click as the breaker resets. If the breaker trips again, or simply won’t reset, there may be a problem with your wiring.

How to fix a tripping circuit breaker

Check to see if the circuit breaker is damaged.

If the circuit breaker trips and won’t reset, the first thing you should do is check to see if the switch is damaged. Circuit breakers are designed to trip when they become overloaded, which means they’re also designed to be flipped back on when the overload is resolved. However, if the switch itself is damaged or the electrical panel is outdated , it may not reset properly.

To check for damage, first make sure that there’s no power going to the breaker box by flipping all the switches to the “off” position. Then open up the panel and visually inspect the faulty breaker for any signs of burned or blackened areas. If you see any charring or burning around the switch, it’s likely time to replace it.

In some cases, you may be able to reset a damaged breaker by gently bending the switch back into place. However, this is only a temporary fix and the breaker will eventually need to be replaced.

We recommend that if you see any damage, it’s best to replace the entire circuit breaker rather than just the switch.

Check to see if there’s an electrical short

Another reason why your circuit breaker won’t reset after tripping is because there’s an electrical short somewhere in your home. An electrical short occurs when there’s too much current flowing through a wire, causing it to overheat and potentially start a fire.

To figure out if there’s an electrical short, the first thing you should do is turn off all of the switches in your breaker box. Once everything is off, go around your home and look for any signs of an electrical fire, such as burning smells or smoke. If you see or smell anything suspicious, call a licensed electrician right away.

If you don’t see any signs of a fire, the next step is to identify which circuit is causing the problem. Start by flipping on one switch at a time and seeing if the breaker trips. If it does, leave that switch off and move on to the next one. Repeat this process until you’ve found the problem circuit.

Once you’ve identified the problem circuit, the next step is to figure out where the electrical short is located. The easiest way to do this is to start at the breaker box and work your way down the circuit until you find the problem.

If you’ve followed these steps and you believe there may be an electrical short, it’s important to call an electrician right away. They’ll be able to locate the source of the problem and fix it before it causes any further damage.

Check for loose wiring

Another common reason for a circuit breaker to trip is because of loose wiring. Over time, wires can loosen and become frayed, which can cause them to short circuit.

The best way to check for loose wiring is to listen to your devices and appliances for the sound of buzzing or crackling. One common culprit is buzzing light switches or outlets. If you don’t find a faulty appliance, note that this can also be true around the breaker.

If you hear these noises and suspect that your circuit breaker is tripping because of loose wiring, the best thing to do is call an electrician as soon as possible. Trying to fix the problem yourself could result in injury or even death.

An electrician will be able to quickly diagnose the problem and make the necessary repairs. In most cases, they’ll also be able to prevent the problem from happening again in the future.

Look for signs of corrosion

Another common reason for a circuit breaker to trip is corrosion. This is especially true if you notice any moisture or wetness in the electrical panel . Corrosion can cause the metal parts of the breaker to break down, which in turn can cause a short circuit.

Corrosion usually appears in the form of a white, chalky substance building up around screw terminals. Look for signs of corrosion, rust, or moisture around the circuit breaker.

If you suspect that corrosion is the culprit, call an electrician to have a look at the problem. Trying to clean or repair the corrosion yourself could result in serious injury.

Check for damaged insulation

Sometimes circuit breakers will have insulation around them to stop cold air from entering through the box itself. Damaged insulation is another common cause of tripped circuit breakers. If you have insulation around the box, inspect it to see if it looks damaged.

If the insulation around your electrical wiring is damaged, it could cause a short circuit. Once again, if you suspect that this is the problem, call an electrician rather than trying to repair the problem yourself.

Is it dangerous if a circuit breaker keeps tripping?

We are often asked if tripping circuit breakers are dangerous. If your circuit breaker keeps tripping, it could be a sign of an electrical problem in your home, up to and including serious fire risks. While it’s not necessarily dangerous if your circuit breaker trips occasionally, if it happens frequently, it should be fixed right away.

If your circuit breaker trips and won’t reset, don’t panic! Many times the problem is something minor that you can easily fix yourself. However, if you’re unsure of what to do or think the problem may be something more serious, always err on the side of caution and call an electrician . Trying to fix the problem yourself could result in serious injury or even death.

Resetting a tripped circuit breaker is a relatively simple process that most people can do on their own. However, if the breaker trips repeatedly or if you have any questions about your electrical system, it’s always best to contact a professional electrician for assistance.

If you have any questions about resetting your circuit breaker or if you need assistance from a professional, don’t hesitate to contact us . We’re here to help!

Latest Articles

Average Electrician Cost to Install an EV Charger

Light Switch Buzzing: Causes, Dangers, and Fixes

How Many Things Can I Plug Into One Outlet Safely?

Commercial Outlet Vs Residential Outlets: Which is Right for You?

Are Ungrounded Outlets Dangerous? Understanding the risks

Why is My Outlet Smoking? Potential causes and how to fix them

Copyright © 2023 Clocktower Electric, LLC. All rights reserved. St. Simon’s Island, GA 31522

Contact Us | Privacy Policy | Site Map

• Areas We Serve
• How We Help
• Credentials
• Compliments
• Electrical Installations & Repairs
• Electrical Home Renovations
• Electrical Safety Inspections
• Knob and Tube Wiring Replacement & Repairs
• Aluminum Wiring Repairs
• Lighting Installation
• EV Charger Installation
• Service Panel Upgrade
• New Construction
• Electrical Tenant Improvements
• Industry Links
• Request Quote

What to Do If Your Circuit Breaker Trips

Basically, electric current flows into your home into the breaker box (usually built in the garage or in the basement in the home) where it’s split into a number of circuits and sent throughout the house.

For rooms that only need electrical power for small things like lighting fixtures and televisions, you usually only need 15-amp circuits. For rooms with bigger appliances, such as the kitchen or bathroom, you’ll usually have 20-amp circuits. Certain appliances, like the oven or dryer, are so power consuming they need 30 – 50-amp circuits all to themselves! When it is said that a circuit breaker “trips,” it means that circuit has detected what’s known as a fault condition and has shut itself off to prevent the wiring from overheating and potentially igniting itself.

Resetting a tripped circuit breaker is generally pretty easy – you just need to go back to the electrical panel, find the circuit that’s not facing the same direction as the rest and flip it back to it’s original setting. If the breaker trips again right after you do this, that’s a problem – you’ll have to figure out the cause of the problem before you can fix it.

If your circuit breaker trips right after being reset, you could be facing one of three issues:

•  an overloaded circuit
•  a short circuit
•  a ground fault

Overloaded Circuit

An overloaded circuit is the most likely problem that would make your breakers trip. In simple terms, it means there is more current flowing through the circuit than it is made to carry, so it shuts off to stop any damage.

Remember earlier when we spoke about the different levels of current certain rooms in your home receives? When you are searching for an overloaded circuit, try finding any appliances on the overloaded circuit that would be using more electricity than the circuit would allow. Pay extra attention to objects such as space heaters, toasters, hair dryers straighteners, etc. – These things tend to consume the most power.

The solution for overloaded currents is pretty simple – just unplug things you’re not using! If this doesn’t solve the issue, call an electrician – you may have loose connections somewhere in the house, though this is pretty rare.

Short Circuit

If the problem is not being caused by an overloaded circuit, most likely a short circuit is the issue. Short circuits are a slightly more serious problem than overloaded circuits, which happens when the hot (black) wire touches another hot wire or a neutral wire. The surest way to tell if you are having a short circuit is to first check your power cables for damage or a melted covering (make sure the appliance is unplugged first)  and to check the power outlets or plugs for discoloration or a burning smell. If you can’t locate the problem, hire an electrician to take a look at it.

Ground Fault

If you’ve looked at the two other possibilities and checked for problems, but you don’t think you have an overloaded or a short circuit, you should check to see if a ground fault is causing your troubles. A ground fault exists when the hot (black) wire touches the ground (bare) wire or the walls of a metal outlet box. If you have a ground fault, it’s best to have a  Vancouver electrician take care of the problem.

Need an Electrician?

We provide electrical services for your home, strata or commercial property in Vancouver, BC - We are a Licensed & Insured Electrician Contractor.

[email protected]

604-800-1665

170-422 Richards St., Vancouver, BC V6B 2Z4

Request a Quote

Copyright © 2010-2019 WireChief Electric Ltd. All Rights Reserved. 3rd Floor - 422 Richards St.#170, Vancouver, BC Canada V6B2Z4. Phone: 604-800-1665

Website By Karoline Urena

How To Fix a Tripped Circuit Breaker: Exploring Repair Options

A circuit breaker tripping occasionally is no cause for much of a concern. But if it trips repeatedly, that’s cause for worry. 

The circuit breaker is designed to cut the power off if the electrical current flowing through is at a level deemed unsafe, which is when it trips. Once a circuit breaker trips, you cannot use any switches, outlets, or any fixture it serves.  

Read on to learn how to fix a circuit breaker after tripping.

What is a Circuit Breaker?

A circuit breaker is an electrical safety device. It’s designed to protect an electrical circuit from damage from a short circuit, ground fault, or overcurrent. 

The circuit breaker interrupts current flow when an excessive amount of energy flows. That way, it protects your equipment and prevents the risk of fire.

Steps in Fixing a Tripped Circuit Breaker

Here’s how to fix a tripped circuit breaker :

Step 1: Reset the Tripped Circuit Breaker

Before resetting a tripped circuit breaker, take the necessary precautionary measures. Turn off your appliances, switches, or lights on that electrical circuit. The floor and your hands should be dry to avoid shock.

• Locate the electrical panel–usually located in the utility room, basement, garage, or hallway.
• Review the map or list of rooms each breaker serves. Find the one corresponding to the issue.
• Turn the tripped breaker to an off position, then back on. You should hear it click into place.
• Switch on the lights or appliances on that circuit.

Step 2: Check for Any Circuit Issues

If you reset the tripped breaker to no avail or the circuit breaker trips again, it’s time to troubleshoot. Some potential issues:

• One specific device causing issues: Unplug and connect the device to a different source. You may need a new device instead.
• Too many devices on one circuit. Unplug some devices. If the breaker works, it means you were causing circuit overload. 
• Damage. If your terminal plugs are too hot to touch or sockets appear scorched, it means an electrical power issue is triggering the tripping. 
• Broken switches. If the breaker trips after switching on lights or turning on a particular fixture, you might have a broken switch.

Step 3: Test the Circuit Breaker

To test the circuit breaker box, turn off everything on it. Remove the screws from the frame around the breakers and remove the frame. With the panel exposed, use the 120V multimeter AC voltage to test it.

Attach the black prong to the breaker’s neutral wire and the red one to the hot wire. If the circuit is okay, the reading will be 120V. But if faulty, it will read zero.

How to Replace a Broken Circuit Breaker

You cannot repair a circuit breaker once the fuses are damaged. You must replace it. You can do so by following these steps:

• Turn off the branch circuits before turning off the main breaker.
• Use a voltage tester to check that no electricity is running from the fuse box.
• Use a screwdriver to disconnect the wiring that’s attached to the faulty breaker.
• Carefully pull out the old circuit breaker and fit in the new one accordingly.
• Next, attach the load wire to the terminals and tighten its screws.
• Replace the panel cover and turn on the main breaker, followed by each branch circuit, one at a time.
• Finally, use the voltage meter to test each breaker. Try each appliance and fixture on the circuit to ensure it’s working.

How to Avoid Tripped Breakers

• Avoid running many appliances and devices on the circuit simultaneously.
• Transfer some devices from the overloaded circuit to other circuits drawing less power.
• Consider installing GFCI outlets. These ensure the outlet shuts off in case of a ground fault before the breaker trips.
• Replace old fixtures, outlets, cords, and light switches.
• Replace the circuit breaker.
• Consider having an electrician separate hardwired devices drawing too much power from a single circuit. They can relieve the load by creating an entirely new circuit and moving them there.

Got Circuit Breaker Problems? Contact U.S. Electric Now!

The electrical panel and circuit breakers are vital for the circuitry of every home. If you have circuit breaker issues, leave it to the professionals to handle them. Our experienced, skilled, and licensed electricians are trained to identify the causes of tripped breakers and fix them right away. Note that any electrical troubleshooting is risky, so the best option is to hire the pros. For more info, call U.S. Electric today!

Recent Posts

• How To Install a Ceiling Fan Without Attic Access: A Step-by-Step Guide
• Here’s Why Your GFCI Outlet Won’t Reset
• Why Do Smoke Detectors Beep at Night?
• Do You Need Electrical Panel Repair or Replacement? Here’s How To Tell
• Here’s Why Your Motion Sensor Lights Aren’t Turning On

1335 Martin Luther King Jr Ave

Dunedin, fl 34698, (727) 648-6101.

1335 Martin Luther King Jr Ave, Dunedin, FL 34698

CALL US:   (727) 648-6101

What Does a Circuit Breaker Tripping Mean?

 when there's a circuit breaker tripping, it can indicate that the circuit breaker detects an electrical issue, and it shouldn't be ignored..

The pandemic-induced surge in home electricity use is real. Consider that, according to the National Bureau of Economic Research, American spending on  home power consump tion  skyrocketed by $6 billion! 

With more usage comes more problems, and circuit breaker issues are among the most common. When there's a circuit breaker tripping, it can indicate that the circuit breaker detects an electrical issue, and it shouldn't be ignored.

 Circuit Breaker Tripping 101

Most circuit breaker issues center around circuit overload. Circuit breakers are a vital part of your home's electrical system since they are designed to prevent costly and damaging surges in electrical current. 

The breaker, working in tandem with a fuse, serves as an electrical unit's internal sensing mechanism. At the slightest sense of excess current, the circuit breaker will "trip," triggering a cease in all electrical activity within the circuit.

Not only can such a smart mechanism help with preventing damage to wires and other electrical components, but circuit breakers can also save lives by preventing electrical fires. According to the National Fire Protection Association,  electrical failures  were the second leading cause of home fires between 2012-2016.

So why do circuit breakers trip? Here are the three most common reasons for circuit breaker tripping and how you can go about fixing a circuit breaker.

 1) Circuit Overload

By far, the m ost common reason a circuit trips is because it's overloaded. Even running a circuit at its electrical capacity can cause home appliances to burn out or a circuit to trip. Ideally, you want to run a circuit below its capacity to keep it from tripping and to prevent any damage from occurring. 

The most familiar example of circuit overload is an over-stuffed power outlet. When you have a dozen gadgets all demanding electrical current to work, eventually that single outlet's capacity will experience overload, and the circuit will trip.

Knowing what each electrical outlet in your house can handle is key to preventing circuit overload. Even a single high-current appliance like a washing machine cannot plug into just any outlet.  Understanding your power outlets  is critical for a safer home.

Before you head to your circuit breaker box or call your electrician, notice what was plugged in at the outlet where the tripped circuit occurred. You may have overloaded it.

 2) Short Circuit

Similar to an overload, when a circuit "shorts," it responds to more current than it can bear. But a short circuit is far more dangerous. 

A short circuit occurs when a "hot" or active wire comes into contact with either another active wire or a neutral wire. The touching wires cause a spike in current that can likewise trip your circuit breaker. Most often, the causes for short circuits are mechanical issues like: 

• Loose Connections
• Improper Wiring
• Damaged Wires

Faulty components, like switches, plugs, cords, appliances, or lighting fixtures, are often culprits of short circuits. Short circuits can occur if you screw or nail into drywall and penetrate an electrical wire.

Remember that short circuits may involve faulty circuit wiring, but the device you're plugging in can cause the problem as well. Keep this in mind, especially if you're using older devices or gadgets that have been out of commission for years, as these can be more prone to short circuits, independent of what's going on in the outlet.

Due to their volatile nature, short circuits are some of the biggest causes of electrical fires, so be extra attentive and don't hesitate to call a professional. As a general rule, most people should never  DIY electrical issues  in their homes.

 3) Ground Fault Surge

 Ground fault surges are similar to short circuits because they involve a sudden spike in current, creating an overload. Ground faults occur when an active wire comes into contact with the ground wire. The contact can come directly or indirectly via the metal housing that connects to the ground wire. 

Copper grounding wires are especially prone to ground fault surges. Copper is the most  conductive material  in everyday use when it comes to home electrical systems. When a hot wire touches the ground wire's copper coating, it results in superconductivity that overwhelms the circuit. A similar result can come from an active wire touching a ground's metal outlet box. 

 Understanding and Fixing Circuit Breaker Issues

So how should you go about troubleshooting a circuit breaker issue? Even though you should leave anything remotely technical to a professional, there are a few things you can do to investigate circuit breaker trip meaning.

First thing's first. Make sure you and your family are safe. Check for signs of excess heat or burning—smell for what could be smoke from an electrical fire. If you sense any signs of a fire, evacuate and call 911.

Check for any discoloration around an outlet. Also, make a note of any sparks or popping noises coming from the outlet. Any of these could be a sign of a ground fault surge or a short, in which case simply flipping the circuit breaker switch won't help. And remember, the older the outlet, the more likely it is to experience problems.

Look for any signs of damage to your devices. Remember that the problem could be coming, not from your home's outlet, but from what you plugged in.

If there are no signs of a blown circuit, try going to your circuit breaker service panel. You may be familiar with this metal box, often located in a garage or utility room. Flip the switch of the house area that tripped, and see if that "resets" the circuit. 

 Fixing a Circuit Breaker

If a simple flipping of the switch doesn't work, it's time to call a professional electrician. The seasoned team at Buell Electric can assess the problem and fix a circuit breaker, which may involve repairs or upgrades. 

Circuit breaker tripping may be as innocent as overloading an outlet, but it can point to more serious problems as well. The best way to know for sure is to  contact us  today.

Newer Post >

Buell Electric's Blog

Shedding Light on Your Home: Finding the Right Electrician in Tampa

How Electricians Keep Up with Changing Technology in the Industry

The Importance of Regular Electrical Maintenance For Your Business

Marine Electrical Standards and Regulations You Need to Know

The Benefits of Installing a Smart Home System

Understanding the Different Types of Electrical Wiring in Your Home

How to Prepare Your Home for an Electrical Emergency

5 Reasons Your Ceiling Fan Installation Should be Left to the Pros

5 Tips for Hiring Residential Electrical Services

8 Common Outdoor Lighting Mistakes and How to Avoid Them

[email protected]

Mon-fri 9:00 am - 5:00 pm sat-sun 10:00 am - 5:00 pm privacy page, connect with us:.

Mon-Fri 9:00 AM - 5:00 PM Sat-Sun 10:00 AM - 5:00 PM

All Rights Reserved | Buell Electric, Inc.

AC Breaker Keeps Tripping Breaker: 9 Common Culprits & Fixes

“My AC keeps tripping the breaker. What’s wrong? How do I stop my AC from tripping the breaker?”

AC tripping the breaker is annoying. Even more troublesome, repeatedly trying to run an air conditioner that keeps tripping the breaker can result in permanent damage to the AC unit. So, easy on the breaker reset button ; you should diagnose and fix the problem first.

Here is what might be happening with your air conditioner:

• Air conditioner trips the breaker immediately . When you turn the AC unit, the breaker will flip immediately or only after a few seconds.
• AC trips breaker after 5 minutes or so. The AC starts OK, but after a few minutes, the breaker will trip. This, for example, is typical for the AC compressor tripping breaker (outside AC unit tripping breaker).
• AC trips breaker after a few hours . An air conditioner will work fine for several hours before it trips the breaker.

To help everybody out, we are going to look at how to check why the AC unit keeps tripping the breaker. We are going to check for 9 key culprits that cause the AC circuit breaker to keep tripping.

There are only two roots for why your AC keeps tripping:

• You have a faulty breaker . This involves issues with circuit breaker, AC wiring, and electrical short circuits.

As every HVAC professional does, you should check these culprits one by one, eliminating the causes as you go. Once you have correctly detected what is causing the AC breaker to keep tripping and fix the problem, your AC unit should work smoothly again.

Note: For every culprit, we are going to tell you if it causes the AC breaker to trip immediately, after a few minutes, or after a few hours, and explain why.

Here are the most common culprits (listed one by one) for any air conditioner type – be it central air, mini split, portable, or window air conditioner – to keep tripping the breaker. We are going to start with breaker-related issues (#1 to #3) and continue with AC unit-related issues (#4 to #9) :

Table of Contents

#1 Circuit Breaker Is Bad, Loose, Or Undersized (Causing AC To Trip Breaker Immediately)

If you are lucky, the AC breaker keeps tripping due to a bad breaker. This is one of the easiest problems to solve; problems with the AC unit itself are harder and costlier to fix.

It’s not uncommon to see a bad circuit breaker. Both new and old breakers can go bad due to wear-and-tear or acute amp surge that fries the breaker. Over time, even well-installed circuit breakers can come loose and cause all sorts of issues, including tripping unexpectedly.

In limited cases, we also see that homeowners have installed a circuit breaker that is just too small. Example: A 3-ton AC unit on 220V has a max. wattage of about 3,600 watts and requires a 25A or 30A breaker. You can check what size AC breaker you need here accounting for NEC 80% ampacity rule .

Dead giveaways of a bad breaker are:

• Breaker smells like something is burning.
• Breaker is hot to the touch.
• Breaker keeps tripping all the time.

Solution: First, you need to check if you have a bad breaker. Secondly, check if the breaker is loose; try to nudge it from left to right to set it back in the required position. Of course, you will also have to check the above article if indeed your breaker is big enough to handle all the amps that you need to run your AC unit.

If you have a bad breaker, you just simply replace it. Get a new one – circuit breakers are quite inexpensive – and be sure to check that it has the same ampacity as the old one. Everybody can DIY breaker replacement; you can consult this guide on how to replace a circuit breaker if you need some help.

Once you have a working breaker again, your AC should stop tripping it.

#2 Wrong AC Wiring (New Air Conditioners Trip Breaker Immediately)

Another possibility, especially for new air conditioners, is wrong wiring. If you have a newly wired thermostat or you have just replaced an old thermostat, chances are that not all wires are connected to the right sockets.

For air conditioners, you will have to connect:

• Blue or yellow wire is meant for cooling. These wires are connected to the Y terminal in a standard thermostat.
• Red fire for power, connected to R.
• Common wire (usually black) connected to C.

For more advice on how to wire a thermostat, you can consult the thermostat wiring guide here .

Wrong wiring will lead to the outside AC unit tripping breaker immediately (central aircon or mini splits). This is a standard AC compressor tripping issue; the compressor creates a surge of amps that can hit an undersized breaker if it’s wrongly wired.

Solution: Check that all the wires are in the right sockets. In limited cases, you will have to can an electrician to fix this, but most people can use the guide cited above to adequately wire a thermostat themselves.

#3 Electrical Short Circuit (Unsheathed Wires Touching)

Any short circuit can cause a spike in electrical current (amps) that will trip the breaker. In fact, one of the reasons why we use circuit breakers in the first place is to protect our circuits against short circuits.

In the case of wiring air conditioners, the short circuit happens when two exposed wired (unsheathed because the coating has been degrading for years) touch.

Example: Let’s say that the blue and red wire touch. This doesn’t happen if they are properly insulated. However, over time, insulation can decay. When this happens, the electrical current from two wires will travel along a single wire (the one with the least electric resistance, according to Ohm’s law). This will cause a spike in amps that can knock out the breaker.

Admittedly, it’s very difficult to tell if you are experiencing a short circuit. You do have to go to check all the wires to see if the insulation is damaged. This short circuit problem also causes the AC to trip break immediately, after 5 minutes, or even after 10 hours of running the AC unit. It is not time-specific which makes the detection even harder.

Solution: If you suspect that your AC unit tripping the breaker due to a short circuit, you can check the wires yourself or call an electrician. Once you find faulty wires that are causing the short circuit, you have to reapply the coating, or, in more cases, just replace the wire.

All of this, of course, is easier said than done.

Once you have eliminated the thermostat-related problems, you can start checking if there is something wrong with your air conditioner unit, resulting in the breaker tripping repeatedly:

#4 Dirty Condenser Coils (Causing Outside Air Conditioner Circuit Breaker To Trip)

A lot of AC tripping breaker problems are caused by the air conditioner overheating. One of the most common examples of this is the air conditioner circuit breakers outside to trip.

The outdoor condenser coils are exposed to the environment. That means that anything from dirt, leaves, dust, and grass, can find its way into the AC outdoor unit (you may even find a dead rat in there) . If this dirt accumulates on the fairly exposed condenser coils, you will have problems with the outdoor AC unit tripping breaker.

These condenser coils are basically superb heat exchangers . They expel all the heat that is generated in the refrigeration cycle. If these condenser coils are coated with dirt, for example, their ability to conduct heat is impeded. Obviously, if the coils can’t give away enough heat, the whole outdoor unit will get overheated.

And overheating leads to the AC tripping the breaker.

In this case, the AC breaker won’t turn trip immediately. It won’t even trip in 5 minutes or so. Dirty condenser coils are one of the most common reasons why the AC trips breaker after a few hours. The AC will overheat in time and that can take anywhere from some 10 minutes to several hours.

Solution: Clean the outdoor condenser coils. Open the outdoor unit and check if there is dirt coating on the coils. If there is, clean out the debris and spray them with detergent or coil cleaners. You can read how to clean the condenser coils on the Carrier website here .

After the outdoor coils are cleaned, they can adequately exchange heat again. That means that all the heat that has to be expelled via the coils will be released into the atmosphere again. As a result of the AC unit not overheating, you will no longer have a problem with AC breaker tripping.

#5 Dirty Air Filters (Restricted Airflow Results In Overheating And Trips Breaker)

Dirty air filters are another common culprit for an AC unit to trip breaker after a few hours.

We all know that every AC should have adequate airflow. If the filters are dirty, they restrict the airflow. This can cause a series of unwanted issues and will eventually lead to AC overheating. And, as we know, if the AC is overheating, it will inevitably trip a circuit breaker.

Everybody pretty much knows what to do with dirty air filters, right?

Solution: Clean or replace the air filters. This will again enable the AC unit to operate at sufficient airflow. The AC unit will not overheat. The AC breaker will not trip. It’s a pretty simple fix.

#6 Compressor Fails To Start (Or Hard-Starting Compressor)

Out of all the things that may go wrong, the compressor-related issues are the worst. When you have a faulty compressor, you will in almost all cases have to replace it. This replacement can be so costly that homeowners with older units usually just replace the whole air conditioning system.

Now, if you have a faulty compressor (the reason might also be a fault capacitor), you can expect two things to happen:

• Compressor doesn’t start at all. Regardless of this, the AC compressor can still trip the breaker. You will notice that in this case, the AC compressor trips the breaker immediately.
• Compressor starts slowly (usually takes a few seconds) . This is an indication of a faulty compressor and might lead to the AC compressor tripping the breaker after a few minutes.

The compressor – the main part of the AC – is responsible for compressing the refrigerant gas. If it doesn’t do its job, the AC unit might start overheating and blowing warm (instead of cold) air.

When the compressor doesn’t start at all, there is usually a spike in amps along the compressor wire to the breaker. This will trip the breaker immediately.

If you have a hard-starting compressor, the breaker won’t trip immediately. Nonetheless, such a compressor repeatedly can repeatedly send amp spikes towards the breaker in order to keep running. Eventually – usually in a few minutes or so – one of these amp spikes will overwhelm the circuit breaker and the breaker will flip.

Solution: This is a hard pill to swallow but you will probably have to replace the AC compressor. This is a complex replacement process you can’t do yourself; you will require an HVAC professional to do it for you.

You can, of course, take this ‘opportunity’ to replace the AC unit altogether. If your AC unit is past its prime (15+ years old), replacing the whole air conditioner makes sense in many cases.

#7 Compressor Is Grounded (Wires Touching The Sides)

Another problem a compressor might have – much less troublesome – is some wire displacements. Namely, the electrical wires that power the compressor are unsheathed and touching the compressor casing. It’s always best to check if everything is OK with the compressor wires.

Of course, if the wires touch the metal casing, all that electricity will go to the ground (we talk about the compressor being grounded). Inevitably, this will cause a spike in amps that will knock out the breaker.

Now, this may happen when you turn on the AC, after a few minutes, or even after several hours. The vibrations in the compressor pretty much displace one wire so much that it touches the casing, and that may happen immediately or even after some hours.

Solution: Check if all the wires that go in and out of the compressor still have their insulation coating on them. Also, check if the wires are neatly packed and away from the casing. If you find an exposed wire close to the casing, it’s very likely this is the wire that keeps tripping the AC breaker.

Use a plastic or nylon line to fix the wire in place, away from the casing. You can even replace that wire if you see that the insulation coating is severely damaged. After you do that, your breaker should stop tripping.

#8 Low Refrigerant Levels (Lines Leaking Freon)

All air conditioners work based on the refrigerant cycle. For this cycle to work properly, the lines have to be full of freon (refrigerant gas like R22, R410A, and so on). If you have a leak in the refrigerant lines, there will be less refrigerant within the lines which will lead to AC overheating and potentially tripping the breaker.

Example: If your window AC keeps tripping the breaker, the refrigerant leak could be the culprit.

Solution: You have to check if the refrigerant levels are indeed low by measuring the refrigerant pressure. If freon is indeed leaking out, you will first have to seal the leak and then recharge the AC unit.

In most cases, you will need professional help for this.

If you want to know how a professional refills the freon, you can consult this article about how to recharge a window air conditioner .

#9 Faulty Fan Motor (Leading To Overheating And Breaker Tripping)

In limited cases, we also see that a faulty fan motor is responsible for the outdoor AC unit tripping a breaker after a few hours.

The outdoor fan produces airflow that expels the heat into the environment (cooling the condenser coils). That fan is powered by the motor. If the motor doesn’t produce adequate power output, the fan doesn’t produce adequate airflow, and the outdoor AC cooling process is impeded.

This can lead to AC overheating and tripping the AC breaker. This happens when the AC is overheated enough; it takes a few hours (not on start-up or after a few minutes).

Solution: Check if the outdoor fan is spinning. If not, the problem might be a faulty fan motor. You will probably need to replace it. Before you do that, do check out all the reasons why outdoor AC is not spinning here . Namely, a faulty fan motor is not the only reason why the condenser fan is not spinning.

After you fix this and the fan is spinning again, there won’t be overheating, and the outdoor AC unit will stop tripping the breaker.

How To Call If You Need Professional Help?

As we have seen, both the diagnosis of why the AC keeps tripping the breaker as well as the fixes are not a piece of the case.

From checking the breaker to checking if something is wrong with your AC unit, there is quite a lot of knowledge (and experience) that guys fixing AC units should have.

This article was a general overview of the causes for AC to keep tripping the breaker. If, however, you realize you will a professional help, you can turn to your local HVAC companies.

We hope this helps somebody figure out why the AC keeps tripping the breaker and how to go about fixing it by themselves or with professional help.

Related posts:

• AC Making Noise: 5 Air Conditioner Noises + How To Fix Them
• Window Air Conditioner Freezing Up In Summer? Here’s What Is Wrong
• Thermostat Not Reaching Set Temperature: 7 Causes + Fixes
• How To Tell If AC Is Frozen? 3 Tell-Tale Signs (Ice On Evaporator Coils)
• How To Measure Superheat? Easy 10 Step-By-Step Guide

Leave a Comment Cancel reply

Save my name, email, and website in this browser for the next time I comment.

• Schedule an Appointment
• Clearwater: 727-954-4666
• Bradenton: 941-727-0272
• Lee County: 239-374-2770
• Tampa: 813-644-4413

What’s Tripping My Circuit Breaker? 4 Possible Causes

As electricity flows through the wiring in your house,  circuit breakers  serve as critical safety devices that prevent overloads. When too many amps of electricity are pulled into a circuit, both damage and danger result. Wiring can overheat and melt insulation, causing a fire.

A circuit breaker is a more modern, reusable version of a fuse. The breaker constantly monitors the flow of electricity into a circuit, and if for any reason the amperage exceeds the circuit’s rated amount, the breaker trips and the flow of electricity is interrupted at the breaker panel. All outlets on that individual circuit and all devices plugged into it are instantly powerless.

How Much Load Is Too Much?

In a typical residence, circuits in living spaces like bedrooms and family rooms are generally rated for 15 amps. Parts of the home where more amperage is used such as the kitchen or laundry room will be controlled by more heavy-duty circuit breakers rated for 20 amps. Certain high-demand appliances, electric water heaters and central HVAC equipment will typically occupy an individual dedicated circuit and are rated for 30 to 50 amps.

While a tripping breaker is an important safety feature, it can be an annoyance as well, particularly if it happens often. A breaker that trips repeatedly is telling you something important about your home’s electrical circuitry or devices connected to it. Repeated breaker trips should never be simply reset and ignored.

Here are four common causes for a tripped circuit breaker.

Circuit Overload

A circuit overload, which is the most common cause of a breaker trip, occurs when a device plugged into the circuit demands more amperage of electricity than the circuit is rated to supply. This may occur because too many devices are already drawing current on that circuit and the circuit has reached its maximum rated capacity.

The remedy for circuit overload is to re-distribute the load more evenly by plugging some devices into other circuits.

Appliance Issues

Another may occur when a single electrical device draws excessive amps due to an internal malfunction or defect. For example, the electric motor incorporated in an air conditioner compressor may overheat due to internal wear and may pull too many amps. Or a heater or stove that utilizes electric resistance coils to produce heat may begin to cause overloads.

When a single device or component is causing breaker trips, it must be disconnected from the circuit and evaluated to isolate the problem. Repair or replacement of the device is required before it can be plugged back in and utilized safely.

Short Circuiting

A circuit short occurs when an insulated portion of the black “hot” wire physically contacts another black wire or a white neutral wire. This sends a surge of amperage into the circuit that causes the circuit breaker to trip instantaneously.

Short circuits may occur when household wiring degrades due to age and insulation frays or cracks, allowing bare wires to come in contact. Or it may be caused by an internal defect in any device that’s plugged into an outlet on the circuit.

Short circuits should be tracked to their source by looking for any discolored outlets, melted or cracked power cords or any devices that malfunction or emit a smell of burning wire. If obvious external causes can’t be readily identified, the problem is likely within the wiring itself. Leave the breaker switch off and contact a  professional electrician  to trace the problem.

Ground Fault

A ground fault happens when the hot wire in circuit contact either a ground wire or a grounded metal component such as the metal outlet box. A ground fault is simply another version of a short circuit that causes an electrical overload which triggers the breaker to trip in response.

Pinpointing and correcting a ground fault can be done by a qualified electrician using equipment specifically designed to troubleshoot circuitry.

For more information on circuit breaker issues that affect your home, in Bradenton check out Luminous Electric’s  residential electrical repair solutions  or call .

Similar Posts

How To Know If You Need an Electrical Inspection

Everywhere you look—at home, in your office, or out and about town—our society relies on electronics to perform even the most mundane tasks. Electrical equipment and devices are a staple of 21st-century life, but that doesn’t mean they come without hazards. Electricity can be dangerous, and it’s important to ensure that your home or property…

6 Ways to Lower Your Electricity Bill This Winter

According to the U.S. Energy Information Administration, heating and cooling make the largest portion of your annual energy costs. In addition, televisions, computers, and dryers are other large consumers. Consider how you can make smart choices in each of these areas with the following electricity-saving tips. Lower the Thermostat While you want to stay cozy this…

5 Electrical Hazards to Avoid this Holiday Season

Like the song says, it’s the most wonderful time of year. It’s also one of the most dangerous. That’s because electrical hazards pose a very real threat this time of year. Here’s how to avoid them. 1. Incandescent Lights Many people love decorating their houses with Christmas lights, but incandescent lights are noticeably hotter, which…

Dangerous Electric Problems

The electrical system in your St. Petersburg, Florida, home is at the heart of its functioning. Appliances, lights, and even your HAC system all require electricity to operate and work together to help you stay comfortable and go about your daily activities. Unfortunately, there are times when your electrical system may fail you. There are…

Blown Fuses a Persistent Problem? Get an Electrical Panel Upgrade

Dealing with blown fuses in your Sarasota, Florida, home is never a fun experience, but it’s something that impacts many homeowners in the area. It’s especially common among those with older homes since the wiring may not be able to handle the increased electrical demands. If you’re struggling with persistent blown fuses, an electrical panel…

Keeping Electric Bills Low Year-Round

Electricity usage can take a hefty chunk out of a homeowner’s budget. For residents of Sarasota, Florida, summer can hit your electric bill hard, as it usually means running your air conditioner almost continuously. Using less energy during Florida’s humid summers can drastically lower your annual electric bill. These easy tips will help reduce your…

Galvin Power is reader-supported. When you buy via our links, we may earn a commission at no cost to you. Learn more

How to Trip a Circuit Breaker Safely? Important Things to Know

Written by  Edwin Jones  / Fact checked by  Andrew Wright

Are you looking for a way to learn how to trip a circuit breaker deliberately while making sure you won’t damage your electrical system or the breaker itself? If you want to force a circuit breaker to trip without risking your property, turn it off through the panel.

You’ll need to plug in an appliance or turn on lights that are connected to the circuit and the corresponding breaker. Afterward, you need to turn off the breaker from the panel manually. Then, from there you have to check whether it tripped (turned off) as it should. I’ll explain more in the sections below.

Table of Contents

Things You’ll Need Before Starting

1. leave the appliance, gadget, or light on if you know it is being protected by the breaker you’re attempting to trip., 2. go to the panel, open it then locate the breaker., 3. turn off the circuit breaker then check whether the appliances or lights you left on shut off, too., are you still trying to find the breaker or the circuit connected to it, if you want to test a breaker, there are far safer ways to do it.

• The breaker you mean to test
• Safety glasses
• Insulated gloves
• Insulated screwdriver (If necessary)

A couple of safety tips before pushing through with this circuit breaker trip (pardon the pun):

• Keep your distance from wires and anything that might conduct electricity. Don’t be too confident that your safety equipment can protect you 100% of the time!
• Keep in mind that you’ll have to reset the breaker once you trip it intentionally. Be on the watch for electrical sparks when you’re attempting to do this. I suggest not directly facing the breaker when doing so.
• You may have the proper PPE. However, be mindful of factors such as moisture near the panel when handling it. Be sure everything, especially any spot near the panel, is dry before beginning, and don’t forget about your own body!

I don’t recommend purposely short circuiting the switch board or grounding the phase wire at all. Unless you have complete trust that your breaker will trip 100% of the time, don’t bother doing this since you not only risk starting a fire but also electrocuting yourself or anyone helping you.

If you’ve experienced a short circuit or a grounding issue recently and the breaker tripped, that should be a good sign the breaker is still in tip-top shape.

To actually force these electrical issues to happen just to find out whether the breaker is still functioning can make any professional electrician cringe, so I suggest you steer clear of even finding out ways to do them! Go for it if you want to short circuit your appliances and gadgets.

How to Deliberately Trip a Breaker

To safely trip a breaker, don’t depart from the following steps:

Any of these three will do. Just make sure you don’t turn on too many of them, assuming you already have an existing overload problem that you haven’t solved yet.

Turning on an appliance being fed by a circuit connected to the breaker you’re trying to trip equates to opting to trip a breaker from an outlet. Incidentally, if you’re trying to trip an AFCI or GFCI  outlet , you can do so by using the integrated reset button, This video demonstrates how to do it and gives a couple of helpful tips:

Of course, this is assuming you already know where it’s located. If you’re still unaware of this vital information, stop for now and contact your local electrician or electrical company to help you find it.

Want to skip this? Try to search for it in the basement or any utility room. It’s typically shaped like a rectangle and is attached to the wall. Use Google images as a reference.

Have you found the coveted box? Simply open it to look for the breaker. You may need to use a screwdriver to remove the cover.

Once you find the breaker, pull or push its ‘Off’ button. Again, you’re basically tripping the circuit breaker manually by doing this, which is a feature designed by the breaker’s manufacturer. With that in mind, doing this shouldn’t cause any issue, unlike forcing a short or ground to occur.

With the breaker in tripped position, go back to the room where you left the lights, gadgets, or appliances running. They should no longer be running, assuming the circuit and breaker are all aligned when you previously performed the steps. If that’s what happened, then congratulations, you successfully tripped the correct breaker!

If you’re thinking that tripping the breaker deliberately is a good idea just to pinpoint where it’s located in a packed panel, there’s actually a far simpler way to do this.

In fact, this video explains everything you need to do, and what’s even better is that you don’t need to use any specialized tools to complete your search. It’s well worth watching for the valuable knowledge you can gain, that much I’m certain:

What if you’re trying to find the circuit being served by the breaker? If so, then you ought to buy a reliable circuit tracer instead. One benefit of using this tool is that you can safely perform your identifications without having to shut off the entire electrical system, which, in some cases, requires permission from local electrical authorities.

Moreover, I’m going to assume that some of you are planning on tripping the circuit breaker because you’re trying to test if it’s still in working condition. If that’s the case, then you should learn the clues that point to a bad breaker. Check this guide to know how to test a bad breaker now!

Remember, if your circuit breaker tripped and is continuing to do so, the breaker itself may already need replacing. If you decide to trip a circuit breaker on purpose once you’re already having this problem, you’re only putting yourself and your home in greater danger. I suggest you call an electrician immediately if you think this is the issue.

Since there are many types of circuit breakers , there’s more than one way they fulfill their tripping mechanism. If you want to learn how to identify the circuit breaker type, I suggest you refer to the label that’s printed on the breaker itself. It should indicate whether it’s a single-pole vs double-pole , GFCI or AFCI .

Did you find my guide on how to trip a circuit breaker helpful? I recommended this procedure because it’s the only safe way to trip a circuit breaker. If you happen to know another way, please don’t hesitate to share it in the comments. I’d love it if you took the time to share this article, too.

Related posts you may be interested in:

• Resetting a Tripped Circuit Breaker
• The Most Reason Why Circuit Breaker Fail Without Tripping

I am Edwin Jones, in charge of designing content for Galvinpower. I aspire to use my experiences in marketing to create reliable and necessary information to help our readers. It has been fun to work with Andrew and apply his incredible knowledge to our content.